Tag Archives: Usb Phone

RIFF JTAG – Samsung GT-S5360 Galaxy Y Unbrick – Boot repair supported

Posted on by

01.03.2012   Samsung GT-S5360 Galaxy Y Unbrick – Boot repair supported

Resurrecting Samsung S5360 is easy. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5360:

  •  Solder JTAG cable to Samsung S5360 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung S5360 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
  •  If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

.

RIFF JTAG – Samsung SGH-i777 Galaxy S II Unbrick – Boot Repair supported, World First ! ! !

Posted on by

28.02.2012    Samsung SGH-i777 Galaxy S II Unbrick – Boot Repair supported, World First !  ! !

Samsung I777 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I777:

  •  Solder JTAG cable to Samsung I777 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I777 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung GT-P6800 Galaxy Tab 7.7 Unbrick – Boot repair supported, World First !

Posted on by

27.02.2012    Samsung GT-P6800 Galaxy Tab 7.7 Unbrick – Boot repair supported, World First !

Samsung P6800 is based on the Exynos Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
To resurrect Samsung P6800:

  •  Solder JTAG cable to Samsung P6800 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P6800 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung Galaxy Precedent SCH-M828 Unbrick supported

Posted on by

09.02.2012     Samsung Galaxy Precedent SCH-M828 Unbrick supported

Samsung M828 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung M828 do this:

  •  Solder JTAG cable to Samsung M828 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung M828 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter Download Mode;

_

RIFF JTAG – Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported

Posted on by

10.01.2012     Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported

Samsung T759 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung T759:

  •  Solder JTAG cable to Samsung T759 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Attach battery connector;
  •  Make sure Samsung T759 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

_

RIFF JTAG – Samsung Galaxy Fit (GT-S5670) Unbrick – Boot Repair supported

Posted on by

05.01.2012 Samsung Galaxy Fit (GT-S5670) Unbrick – Boot Repair supported

Samsung S5670 resurrection is simple. Make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5670 do this:

  •  Solder JTAG cable to Samsung S5670 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung S5670 is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power On key on the phone;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;

_

RIFF JTAG – Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported

Posted on by

29.12.2011      Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported

Samsung I9220 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9220 AP:

  •  Solder JTAG cable to Samsung I9220 AP JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9220 AP is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

_

RIFF JTAG – Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Posted on by

28.12.2011    Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Samsung N7000 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung N7000 AP:

  •  Solder JTAG cable to Samsung N7000 AP JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung N7000 AP is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

_

RIFF JTAG – Unbrick Samsung Galaxy TAB Wi-Fi (P1010), more CDMA Models supported

Posted on by

22.11.2011  Unbrick Samsung Galaxy TAB Wi-Fi (P1010), more CDMA Models supported

Samsung P1010 is based on the OMAP3630 (ARM core is Cortex-A8).

Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
Please note, in most cases you will be required to insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot before starting resurrection. In case you don’t have such card yet, you can create it on the “Samsung P1010 RIFF™ MagicCard” page of the resurrector settings dialog.
This is IRAM version of the Samsung P1010 resurrector. We recommend you using it only in case you had problems connecting to phone with normal Samsung P1010 resurrector DLL.

To resurrect Samsung P1010:

  •  Solder JTAG cable to Samsung P1010 JTAG pads;
  •  Insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P1010 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
There are two DLL-s (Normal and iRAM version) – You can use iRam version in case normal one doesnt work properly. iRam version is much slower, but more robust.
CDMA Models added today :
  • ZTE  AC2766
  • ZTE  AC2746
  • AnyData  ADU555C
Please click “Check for Updates” button in order to download and install new updates.

RIFF JTAG – Samsung i9003 Galaxy SL Unbrick, Boot repair supported

Posted on by

28.10.2011  Samsung i9003 Galaxy SL Unbrick, Boot repair supported

Samsung I9003 is based on the OMAP3630 (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
Please note, in most cases you will be required to insert Samsung I9003 RIFF™ MagicCard into phone’s SD slot before starting resurrection. In case you don’t have such card yet, you can create it on the “Samsung I9003 RIFF™ MagicCard” page of the resurrector settings dialog.
Due to OMAP3630’s some peculiar TrustZone security features current resurrector may fail to boot: if this happens, use Samsung I9003 IRAM resurrector – which works much slower but boots without problems.

To resurrect Samsung I9003:

  •  Solder JTAG cable to Samsung I9003 JTAG pads;
  •  Insert Samsung I9003 RIFF™ MagicCard into phone’s SD slot;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9003 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.