Tag Archives: Usb Data

RIFF JTAG – Fly IQ285 unbrick – boot repair supported

Posted on by

31.08.2012   RIFF JTAG – Fly IQ285 unbrick – boot repair supported

Repairing bricked Fly IQ285 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector reflashes radio’s boot zones. There are options to reflash BOOT and RECOVERY zones.

To resurrect Fly IQ285:

  •  Solder JTAG cable to Fly IQ285 JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure Fly IQ285 is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Rezound ADR6425 (HTC Vigor) Unbrick, Unlock, IMEI and CID repair supported

Posted on by

14.08.2012 RIFF JTAG – HTC Rezound ADR6425 (HTC Vigor) Unbrick, Unlock, IMEI and CID repair supported

Repairing bricked HTC Rezound is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 2.10.0000.
In addition, you can set S-OFF (unlock HBOOT so you will be able to flash any ROM) by clicking “Make S-OFF” checkbox in the resurrector settings.

To resurrect HTC Rezound:

  •  Solder JTAG cable to HTC Rezound JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Rezound is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Explorer (HTC Pico) Unbrick, Unlock, SuperCID IMEI repair

Posted on by

13.07.2012  RIFF JTAG – HTC Explorer (HTC Pico) Unbrick, Unlock, SuperCID IMEI repair

 

Repairing bricked HTC Explorer is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ0310000’.

To resurrect HTC Explorer:

  •  Solder JTAG cable to HTC Explorer JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Explorer is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.

RIFF JTAG – HTC Sensation XE PG5813001 (G18) Unbrick, Unlock, S-Off, IMEI repair supported

Posted on by

22.06.2012  RIFF JTAG – HTC Sensation XE PG5813001 (G18) Unbrick, Unlock, S-Off, IMEI repair supported

Repairing bricked HTC Sensation XE (PG5813001) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 1.29.0000.
There is option to reflash BOOT and RECOVERY zones.
In addition, you can set S-OFF (unlock HBOOT so you will be able to flash any ROM) by clicking “Make S-OFF” checkbox in the resurrector settings.

To resurrect HTC Sensation (PG5813001):

  •  Solder JTAG cable to HTC Sensation (PG5813001) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Sensation (PG5813001) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
.

RIFF JTAG – HTC Rhyme (HTC Bliss) Unbrick, Unlock, SuperCID and IMEI Update via USB Supported

Posted on by

12.06.2012     RIFF JTAG – HTC Rhyme (HTC Bliss) Unbrick, Unlock, SuperCID and IMEI Update via USB Supported

Repairing bricked HTC Rhyme (PI46100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.30.0004 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI4610000’.
There is option to reflash android BOOT and RECOVERY zones.

To resurrect HTC Rhyme via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure HTC Rhyme (PI46100) is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Depower the phone;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Radar (HTC Omega) Unbrick, Unlock, SuperCID and IMEI update via USB cable supported

Posted on by

12.06.2012   RIFF JTAG – HTC Radar (HTC Omega) Unbrick, Unlock, SuperCID and IMEI update via USB cable supported

Repairing bricked HTC Radar (PI06100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI0610000’.

To resurrect HTC Radar via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure HTC Radar (PI06100) is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Depower the phone;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

.

RIFF JTAG – HTC One V T320e (HTC Primo) Unbrick, Unlock, SuperCID, IMEI Repair supported

Posted on by

31.05.2012  RIFF JTAG – HTC One V T320e (HTC Primo) Unbrick, Unlock, SuperCID, IMEI Repair supported

Repairing bricked HTC OneV (PK76100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.16.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK7610000’.
There is option to reflash android BOOT and RECOVERY zones.

To resurrect HTC OneV via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure HTC OneVC (PK76100) is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC 7 Surround T8788 (HTC Mondrian) Unbrick, Unlock, SuperCID and IMEI repair supported

Posted on by

23.05.2012  RIFF JTAG – HTC 7 Surround T8788 (HTC Mondrian) Unbrick, Unlock, SuperCID and IMEI repair supported

Repairing bricked HTC Surround (PD26100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.74.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD26*****’.

To resurrect HTC Surround (PD26100):

  •  Solder JTAG cable to HTC Surround JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Surround (PD26100) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung SGH-T679 Exhibit II 4G (Samsung Ancora) Unbrick – Dead Boot repair supported

Posted on by

04.05.2012 RIFF JTAG – Samsung SGH-T679 Exhibit II 4G (Samsung Ancora) Unbrick – Dead Boot repair supported

Repairing bricked Samsung T679 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is multi-core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.

To resurrect Samsung T679:

  •  Solder JTAG cable to Samsung T679 JTAG pads;
  •  Make sure Samsung T679 is selected in the list of models;
  •  Insert battery and connect USB Data cable;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Flyer WiFi (PG41400) Unbrick, S-off, CID update supported

Posted on by

RIFF JTAG – HTC Flyer WiFi (PG41400) Unbrick, S-off, CID update supported

Repairing bricked HTC Flyer WiFi (PG41400) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Flyer boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so writing to DBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into DBL zone and will respond with success code as if flashing succeeded. In this way DBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL to 1.11.0011 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG4140000’.
There is option to reflash android BOOT and RECOVERY zones. Recovery zone is flashed with ClockworkMod Recovery 4.0.1.4. In addition, you can set S-OFF (unlock HBOOT so you will be able to flash any ROM) by selecting S-OFF HBOOT version in the resurrector settings.
Sometimes (for example after rooting attempts) phone has a modified DBL loader (which may not accept official HTC boot files). To restore phone functionality you need to reflash DBL loader. There is option to reflash DBL code (DBL area will be temporary unlocked for reflashing). But please note, reflashing DBL area is very dangerous, since in case flashing stops in the middle, you will have briked phone with permanently disabled JTAG interface.
Please note, if your phone has the DBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Flyer WiFi:

  •  Solder JTAG cable to HTC Flyer JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Flyer (PG41400) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;


 Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.