Tag Archives: Usb Data

RIFF JTAG – HTC J ISW13HT (HTC Valente) Unbrick – Dead boot repair supported

Posted on by

27.05.2013  RIFF JTAG – HTC J ISW13HT (HTC Valente) Unbrick – Dead boot repair supported

Repairing bricked HTC Valente (PK0710000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK0710000’.

To resurrect HTC Valente (PK0710000):

  •  Solder JTAG cable to HTC Valente (PK0710000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Valente (PK0710000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htcj

RIFF JTAG – HTC Desire VC T328d Unbrick – dead boot repair supported

Posted on by

09.05.2013  RIFF JTAG – HTC Desire VC T328d Unbrick – dead boot repair supported

Repairing bricked HTC DesireVC (PK7810000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.27.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK7810000’.

To resurrect HTC DesireVC (PK7810000):

  •  Solder JTAG cable to HTC DesireVC (PK7810000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC DesireVC (PK7810000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_vc_t328d_2

RIFF JTAG – HTC Windows Phone 8S (HTC Rio) Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

19.04.2013  RIFF JTAG – HTC Windows Phone 8S (HTC Rio) Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC 8S (PM5910002) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM5910002’.

To resurrect HTC 8S (PM5910002):

  •  Solder JTAG cable to HTC 8S (PM5910002) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC 8S (PM5910002) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_windows_phone_8s

RIFF JTAG – HTC Windows Phone 8X LTE 16GB Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

19.04.2013  RIFF JTAG – HTC Windows Phone 8X LTE 16GB Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC 8X (PM2320000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM232****’.

To resurrect HTC 8X (PM2320000):

  •  Solder JTAG cable to HTC 8X (PM2320000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC 8X (PM2320000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_windows_phone_8x_3

RIFF JTAG – HTC EVO 3D CDMA Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

19.04.2013   RIFF JTAG – HTC EVO 3D CDMA Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC Evo3D CDMA (PG8610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 1.50.0000.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC Evo3D CDMA (PG8610000):

  •  Solder JTAG cable to HTC Evo3D CDMA (PG8610000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Evo3D CDMA (PG8610000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc-evo-3d

RIFF JTAG – T-Mobile myTouch 4G Slide (HTC Doubleshot) Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

19.04.2013  RIFF JTAG – T-Mobile myTouch 4G Slide (HTC Doubleshot) Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC MyTouch4G (PG5910000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 1.44.1107.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC MyTouch4G (PG5910000):

  •  Solder JTAG cable to HTC MyTouch4G (PG5910000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC MyTouch4G (PG5910000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

t-mobile_mytouch_4g_slide

RIFF JTAG – HTC Titan X310E (HTC Eternity) Unbrick, Unlock, IMEI and SuperCID repair supported

Posted on by

19.04.2013  RIFF JTAG – HTC Titan X310E (HTC Eternity) Unbrick, Unlock, IMEI and SuperCID repair supported

Repairing bricked HTC Titan (PI3911000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Titan (PI3911000) boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so if DBL area is damanged and MCU has JTAG Disable FUSE blown then there is no way to resurrect your phone via JTAG interface. However, in this case you may use HTC Titan (PI3911000) USB DLL version which does not require JTAG interface and does resurrection procedure via USB cable.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI3911000’.

To resurrect HTC Titan (PI3911000):

  •  Solder JTAG cable to HTC Titan (PI3911000) JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Titan (PI3911000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_titan_x310

RIFF JTAG – HTC Windows Phone 8X (HTC Accord) Unbrick, Dead boot IMEI repair supported

Posted on by

29.03.2013   RIFF JTAG – HTC Windows Phone 8X (HTC Accord) Unbrick, Dead boot IMEI repair supported

Repairing bricked HTC 8X (PM2330000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM2330000’.

To resurrect HTC 8X (PM2330000):

  •  Solder JTAG cable to HTC 8X (PM2330000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC 8X (PM2330000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_windows_phone_8x_2

 

RIFF JTAG – HTC EVO Design 4G PH4430(HTC Kingdom) Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

29.03.2013  HTC EVO Design 4G PH4430(HTC Kingdom) Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC EvoDesign4G is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zones and will re-write PDA’s SPL to 1.30.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH4430000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC EvoDesign4G via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure USB cable is attached to the board and is connected to PC;
  •  Make sure HTC EvoDesign4G via USB is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_evo_design_4g

RIFF JTAG – LG E405 Optimus L3 Dual Unbrick – Dead boot repair supported

Posted on by

29.03.2013  RIFF JTAG – LG E405 Optimus L3 Dual Unbrick – Dead boot repair supported

Repairing bricked LG E405 with the RIFF Box is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E405:

  •  Solder JTAG cable to LG E405 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E405 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.
lg_e405_optimus_l3_dual