Tag Archives: Usb Data Cable

RIFF JTAG – ZTE V889D Unbrick – Dead boot repair supported

Posted on by

09.03.2013  RIFF JTAG  – ZTE V889D Unbrick – Dead boot repair supported
Repairing bricked ZTE V889D is easy with the RIFF Box.

To resurrect ZTE V889D:

  •  Solder JTAG cable to ZTE V889D JTAG pads;
  •  Make sure ZTE V889D is selected in the list of models;
  •  Connect USB Data Cable;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

.
zte_v889D

RIFF JTAG – ZTE Skate Acqua (V880) Unbrick – Dead boot repair supported

Posted on by

09.02.2013  RIFF JTAG – ZTE Skate Acqua (V880) Unbrick -Dead boot repair supported

Repairing bricked ZTE V880 is easy with the RIFF Box.

To resurrect ZTE V880:

  •  Solder JTAG cable to ZTE V880 JTAG pads;
  •  Make sure ZTE V880 is selected in the list of models;
  •  Connect USB Data Cable;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

.
zte_acqua

RIFF JTAG – Samsung Star Duos (C6712) Unbrick – Boot repair supported

Posted on by

29.11.2011  Samsung Star Duos (C6712) Unbrick – Boot repair supported

Samsung C6712 resurrection is simple. Battery is not required. To power the board it’s most convenient to use an USB Data Cable.
In order to contact to JTAG pads you may need to carefully scratch off paint covering (mask layer) above them. Sometimes there is reset problem with these phones, thus you may need to disconnect and then connect USB cable again.

To resurrect Samsung C6712 do this:

  •  Solder JTAG cable to Samsung C6712 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung C6712 is selected in the list of models
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘SIM Swap’ keys and press Power-On.
__

RIFF JTAG – CDMA ZTE R518 supported

Posted on by

28.10.2011   CDMA ZTE R518 supported

Resurrecting ZTE R518 is easy. Battery is not required. To power the board it’s most convenient to use an USB Data Cable

To resurrect ZTE R518:

  •  Solder JTAG cable to ZTE R518 JTAG pads;
  •  Make sure ZTE R518 is selected in the list of models;
  •  Connect USB Data Cable;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

RIFF JTAG – Samsung Corby II – S3850 supported

Posted on by

24.10.2011  Samsung Corby II – S3850 supported

Samsung S3850 resurrection is simple. Battery is not required. To power the board it’s most convenient to use an USB Data Cable.
In orger to contact to JTAG pads you may need to carefully scratch off paint covering (mask layer) above them.

To resurrect Samsung S3850 do this:

  •  Solder JTAG cable to Samsung S3850 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung S3850 is selected in the list of models
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Up’ and ‘Call’ keys and press Power-On.