Tag Archives: Usb Cable

RIFF JTAG – Samsung SHW-M240S Galaxy Ace Unbrick – Dead Boot repair supported

Posted on by

13.02.2013  RIFF JTAG – Samsung SHW-M240S Galaxy Ace Unbrick – Dead Boot repair supported

Repairing bricked Samsung M240S is easy with the RIFF Box. You need to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung M240S do this:

  •  Solder JTAG cable to Samsung M240S JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung M240S is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power On button shortly if it stops on establish conneciton stage;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

.
Samsung-Galaxy-Ace-SHW-M240S

RIFF JTAG – Samsung SHW-M190S GALAXY S Hoppin Unbrick – Dead Boot repair supported

Posted on by

13.02.2013  RIFF JTAG – Samsung SHW-M190S GALAXY S Hoppin Unbrick – Dead Boot repair supported

Repairing bricked Samsung M190S is easy with the RIFF Box. The device is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung M190S:

  •  Solder JTAG cable to Samsung M190S JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Attach battery connector;
  •  Make sure Samsung M190S is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung-m190s-

RIFF JTAG – CDMA Samsung SCH-M569 Unbrick – Dead Boot repair supported

Posted on by

13.02.2013  RIFF JTAG – CDMA Samsung SCH-M569 Unbrick – Dead Boot repair supported

Resurrecting Samsung M569 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.

To resurrect Samsung M569:

  •  Solder JTAG cable to Samsung M569 JTAG pads;
  •  Make sure Samsung M569 is selected in the list of models;
  •  Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
M569

RIFF JTAG – LG SU630 Unbrick – Dead boot repair supported

Posted on by

13.02.2013  RIFF JTAG – LG SU630 Unbrick – Dead boot repair supported

Resurrecting LG SU630 is very easy but it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).

To resurrect LG SU630:

  •  Solder JTAG cable to LG SU630 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG SU630 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
su630_k

RIFF JTAG – Alcatel One Touch OT-995 Unbrick – Dead boot repair supported

Posted on by

09.02.2013  RIFF JTAG – Alcatel One Touch OT-995 Unbrick – Dead boot repair supported

Repairing bricked Alcatel OT995 is easy with the RIFF Box.

To resurrect Alcatel OT995:

  •  Solder JTAG cable to Alcatel OT995 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Alcatel OT995 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

.
alcatel_ot-995

RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

Posted on by

09.02.2013   RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

Repairing bricked HTC OneXL (PJ8312000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8312000’.

To resurrect HTC OneXL (PJ8312000):

  •  Solder JTAG cable to HTC OneXL (PJ8312000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneXL (PJ8312000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_xl

RIFF JTAG – ZTE Skate Acqua (V880) Unbrick – Dead boot repair supported

Posted on by

09.02.2013  RIFF JTAG – ZTE Skate Acqua (V880) Unbrick -Dead boot repair supported

Repairing bricked ZTE V880 is easy with the RIFF Box.

To resurrect ZTE V880:

  •  Solder JTAG cable to ZTE V880 JTAG pads;
  •  Make sure ZTE V880 is selected in the list of models;
  •  Connect USB Data Cable;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

.
zte_acqua

RIFF JTAG – Samsung GT-S6810P Galaxy Fame WORLD FIRST Boot repair support ! ! !

Posted on by

07.02.2013  RIFF JTAG – Samsung GT-S6810P Galaxy Fame WORLD FIRST Boot repair support ! ! !

Repairing bricked Samsung S6810P is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S6810P:

  •  Solder JTAG cable to Samsung S6810P JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S6810P is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘OK’ keys and press Power-On. And after you see the warning message press ‘Volume Up’ key to enter Download Mode.

.
samsung_gt-s6810_galaxy_fame

RIFF JTAG – Samsung YP-G1CW / YP-G1CB Galaxy S WiFi Unbrick – Dead Boot repair supported

Posted on by

05.02.2013  RIFF JTAG – Samsung YP-G1CW / YP-G1CB Galaxy S WiFi Unbrick – Dead Boot repair supported

Samsung YP-G1 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.

To resurrect Samsung YP-G1:

  •  Solder JTAG cable to Samsung YP-G1 JTAG pads;
  •  Connect microUSB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung YP-G1 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_yp-g1_galaxy_s_wifi_40

RIFF JTAG – HTC Droid DNA ADR6435 / Droid Incredible X (HTC DLX) Unbrick, Unlock, IMEI and SuperCID repair supported

Posted on by

RIFF JTAG – HTC Droid DNA ADR6435 / Droid Incredible X (HTC DLX) Unbrick, Unlock, IMEI and SuperCID repair supported

Repairing bricked HTC Droid DNA (PL8320000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.33.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PL8320000’.

To resurrect HTC Droid DNA (PL8320000):

  •  Solder JTAG cable to HTC Droid DNA (PL8320000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Droid DNA (PL8320000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_droid_dna