Tag Archives: Usb Cable

RIFF JTAG – HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported

Posted on by

31.03.2011    HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported

Resurrecting HTC Chief is easy:
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.44.0000 SPL version.
Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘CEDA10000’.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.

To resurrect HTC Chief:

  • Solder JTAG cable to HTC Chief JTAG pads;
  • Make sure HTC Chief is selected in the list of models;
  • Insert battery and connect USB Cable;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – RoverPC EVO V7 Unbrick – Dead boot repair supported

Posted on by

21.03.2011  RoverPC EVO V7 Unbrick – Dead boot repair supported

RoverPC Evo V7 resurrection is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect RoverPC Evo V7:

  • Solder JTAG cable to RoverPC Evo V7 JTAG pads;
  • Connect USB cable to phone and PC;
  • Make sure RoverPC Evo V7 is selected in the list of models;
  • Make sure a fixed TCK frequency is selected;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original firmware downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Huawei C5005 Unbrick – Repair supported

Posted on by

11.03.2011  CDMA Huawei C5005 Unbrick – Repair supported

Resurrecting Huawei C5005 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0xBFFFFF).

To resurrect Huawei C5005:

  • Solder JTAG cable to Huawei C5005 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Huawei C5005 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Tattoo A3232 (HTC Click 1100) Unlock, Unbrick, IMEI repair, CID Update

Posted on by

10.03.2011 HTC Tattoo A3232 (HTC Click 1100) Unlock, Unbrick, IMEI repair, CID Update supported

Resurrecting HTC Click is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside.
There are two different hardware versions exist – one based on the MSM7225 chipset (CLIC10000) and other – on the ESM7225 chipset (CLIC11000). In resurrector settings you can select a desired version.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.52.0001 SPL version.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.

To resurrect HTC Click:

  • Solder JTAG cable to HTC Click JTAG pads;
  • Make sure HTC Click is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To Unlock HTC Click :

  • Solder JTAG cable to HTC Click JTAG pads;
  • Make sure HTC Click is selected in the list of models;
  • Click Resurrect button;
  • Select “Unlock Settings” TAB
  • Select Unlock method
  • Click “Unlock”

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – ASUS P526 Unbrick, Dead Boot repair supported

Posted on by

10.03.2011   ASUS P526 Unbrick, Dead Boot repair supported

Resurrection of ASUS P526 is slightly complicated. JTAG pads are very small and sensitive thus extreme care must be taken when soldering wires to the board. Battery must be connected in order to establish JTAG connection.
Current resurrector re-flashes only the IPL area, and will not re-write MDOC XLOADER area (though write of this area is supported too).
Please note: DiskOnChip G4 memory has security features, due to which there is a risk of permanently blocking the access to the flash memory while re-flashing the XLOADER areas. Current resurrector will not touch the XLOADER zone, but it is possible you’re already holding such killed device in hands. If it is so you will see this error:
****************************************************************
Detected a Not Initialized FLASH1 Chip ID: 0x0400/0xFBFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader
****************************************************************

This can happen due to unknown protection keys used or due to permanently blocked MDOC chip. If latter is true we advise you to solder a new flash memory chip or throw this phone away to the trash bin.

To resurrect ASUS P526:

  • Solder JTAG cable to ASUS P526 JTAG pads;
  • Insert battery and connect USB cable to phone and PC;
  • Make sure ASUS P526 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
If phone not enters download mode after resurrection then it means XLOADER was damaged too but memory chip is still usable. In this case repeat resurrection using RAM Downloader Mode and when USB connection is established reflash the phone with official firmware.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Move ‘Lock’ slider down, hold ‘OK’ key (on the left) and press ‘Power ON’ button. In few seconds you should see TriColor picture.

Additional info:

  • Phone has DiskOnChip G4 memory type, which has security features. It has two password protected partitions (Password1 = 12345678, Password2 = 00000000);
  • XLOADER re-flash is not performed in this resurrector on purpose. While re-flashing the XLOADER area there is a risk of permanently blocking the memory chip.
  • Any write access (Erase or Write) on MDOC NAND memory range 0x00000000 to 0x0017FFFF is rejected by the DCC Loader

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE F285 Repair supported

Posted on by

10.03.2011 CDMA ZTE F285 Repair supported

Resurrecting ZTE F285 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x60FFFF).
To resurrect ZTE F285:

  • Solder JTAG cable to ZTE F285 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure ZTE F285 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Toshiba Tsunagi TG01 Unbrick/EFS Repair/Unlock supported

Posted on by

05.10.2010 Toshiba Tsunagi TG01 Unbrick/EFS Repair/Unlock supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Toshiba_tg01.dll” contains pinout, repair instructions and required files for single click Toshiba Tsunagi TG01 Unlock and unbrick.

Important info ! ! !

To flash TG01 You need the following :
– TG Downloader
– TG USB Drivers
– TG Tool and TSW file or already decrypted bin file
Install TG Downloader and TG USB Drivers first, and reboot the PC.
Connect pin A to pin B on phone and hold the power button. Phone will enter download mode, Windows will find new device, and install drivers.
Start the TG Downloader with admin rights, and open the *.bin file. TG Downloader will report error with version, You need to press YES.
Now You need to select Toshiba DL port in port settings and after confimation, press “Download mode”.
Phone will be booted, and You can press “Download” now.
Now simply wait for download process to be finished.
Credits for this solution go to xda-developers portal!
Tips:
Communication problems with RIFF can occur. In order to avoid it, disconenct LCD and touch panel flex cable connectors. Usually its enough to have Micro USB Cable connected to PC.

In some cases You may need to keep reset switch pressed, in order to finish operation.

To reset Toshiba TG01 to factory state, hold volume+, camera and power buttons together. Phone will start with confirmation screen, using volume keys You need to select <YES> and confirm with camera button.
Screen calibration will be requested after this !


RIFF JTAG – Samsung WAVE S8500 Unbrick/Repair beta support

Posted on by

31.08.2010 Samsung WAVE S8500 Unbrick/Repair boot beta support

This is beta test, and it is not available trough “Check for updates” button.


What You need to repair it ?

– RIFF Box
– Micro USB Cable
– Full charged battery (4.2v)
– CMM + ELF
– Samsung_S8500_PDA.dll
– Pinout
– Multiloader
– USB Drivers
– Firmware files

Procedure:

– Solder RIFF JTAG cable (use very thin wires for PCB, because of battery)
– Insert battery
– Connect Micro USB cable to phone and PC port
– Start the JTAG Manager and select Samsung S8500 PDA from the list
– Switch to “DCC Read/Write” TAB
– Set everything as on photo bellow:

– Press “Read memory” and wait to be finished
– Now switch to “JTAG Read/Write” TAB and press “Connect&Get ID” then “Halt the Target” buttons
– Click “Execute Script” and select CMM file
– Press “Run Script” button

– Ram loader will be uploaded and after its uploaded, phone will automaticaly enter download mode, and detected by PC
– IMPORTANT ! ! ! Now You must disconnect JTAG Cable from RIFF Box
– Start Multiloader 5.62, set “Boot change” and select Boot files folder
– Press download – and wait for process to be finished
– Now phone contains valid bootloader, and can be flashed, so You can desolder JTAG wires from PCB

To enter download mode hold LOCK+Volume Down + Power on Keys.

Problems which You may have:

– Target not detected – check all wires and tp, check battery, 4.2v is a MUST !
– Wrong DCC answer – low battery, or TCK too high, You can use 100KHz TCK too !
– “It not work” – no idea about this lol