Tag Archives: Usb Cable

RIFF JTAG – HTC EVO 4G LTE (HTC Jewel) Unbrick – Dead Boot Repair Supported

Posted on by

16.11.2012    RIFF JTAG – HTC EVO 4G LTE  Unbrick – Dead Boot Repair Supported

Repairing bricked HTC Jewel is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.15.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ7510000’.

To resurrect HTC Jewel:

  •  Solder JTAG cable to HTC Jewel JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Jewel is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-i8530 Galaxy Beam Unbrick – Dead Boot Repair Supported

Posted on by

16.11.2012 RIFF JTAG – Samsung GT-i8530 Galaxy Beam Unbrick – Dead Boot Repair SupportedĐ

Repairing bricked Samsung I8530 is easy with the RIFF Box.
Please note, if you have problems connecting phone, then make sure USB Cable is disconnected, insert battery and press Power On and try connecting again.

To resurrect Samsung I8530:

  •  Solder JTAG cable to Samsung I8530 JTAG pads;
  •  Attach battery;
  •  Disconnect USB Cable (if was connected);
  •  Make sure Samsung I8530 is selected in the list of models;
  •  Click Resurrect button;
  •  If required, press Power On key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – LG E610/E612 Optimus L5 Unbrick -Dead Boot Repair Supported

Posted on by

16.11.2012   RIFF JTAG – LG E610/E612 Optimus L5 Unbrick -Dead Boot Repair Supported

Repairing bricked LG E612 is easy with the RIFF Box. 
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E612:

  •  Solder JTAG cable to LG E612 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E612 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-i8350 Omnia W Unbrick – Dead Boot Repair Supported

Posted on by

14.11.2012   RIFF JTAG – Samsung GT-i8350 Omnia W Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung I8350 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.

To resurrect Samsung I8350:

  •  Solder JTAG cable to Samsung I8350 JTAG pads;
  •  Make sure Samsung I8350 is selected in the list of models;
  •  Insert battery and connect USB Data cable;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-P7320 Galaxy Tab 8.9 LTE Unbrick – Dead Boot Repair Supported

Posted on by

13.11.2012  RIFF JTAG – Samsung GT-P7320 Galaxy Tab 8.9 LTE Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung P7320 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung P7320:

  •  Solder JTAG cable to Samsung P7320 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P7320 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Up’ key (which is closest to Power-On key) and press Power-On.

.

RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Posted on by

13.11.2012 RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Resurrecting HTC WildFireS CDMA is easy with RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 (for NAND chips with 4Kb page size). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG7620000’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS CDMA:

  •  Solder JTAG cable to HTC WildFireS CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC WildFireS CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

.

RIFF JTAG – LG F-160S Optimus LTE2 Unbrick – Dead Boot Repair Supported

Posted on by

09.11.2012 RIFF JTAG – LG F-160S Optimus LTE2 Unbrick – Dead Boot Repair Supported

Repairing bricked LG F160S is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect LG F160S:

  •  Solder JTAG cable to LG F160S JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure LG F160S is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
.

RIFF JTAG – LG F-160L Optimus LTE2 Unbrick – Dead Boot Repair Supported

Posted on by

09.11.2012  RIFF JTAG – LG F-160L Optimus LTE2 Unbrick – Dead Boot Repair Supported

Repairing bricked LG F160L is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect LG F160L:

  •  Solder JTAG cable to LG F160L JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure LG F160L is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
.

RIFF JTAG – LG F-160K Optimus LTE2 Unbrick – Dead Boot Repair Supported

Posted on by

09.11.2012   RIFF JTAG – LG F-160K Optimus LTE2 Unbrick – Dead Boot Repair Supported

Repairing bricked LG F160K is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect LG F160K:

  •  Solder JTAG cable to LG F160K JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure LG F160K is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
.

RIFF JTAG – LG C660 Optimus Pro Unbrick – Dead Boot Repair Supported

Posted on by

08.11.2012 RIFF JTAG – LG C660 Optimus Pro Unbrick – Dead Boot Repair Supported

Repairing bricked LG C660H is easy with the RIFF Box. But it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).

To resurrect LG C660H:

  •  Solder JTAG cable to LG C660H JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG C660H is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.