Tag Archives: Usb Cable

RIFF JTAG – Easy repair Sony Xperia Tipo Dual ST21i2 (Sony Tapioca DS) supported

Posted on by

RIFF JTAG – Easy repair Sony Xperia Tipo Dual ST21i2 (Sony Tapioca DS)  supported

Repairing bricked SE ST21i2 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.

To resurrect SE ST21i2:

  •  Solder JTAG cable to SE ST21i2 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE ST21i2 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
sony_xperia_tipo_dual

RIFF JTAG – Easy repair Samsung GT-i8730 Galaxy Express supported

Posted on by

RIFF JTAG – Easy repair Samsung GT-i8730 Galaxy Express supported

Repairing bricked Samsung I8730 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I8730:

  •  Solder JTAG cable to Samsung I8730 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I8730 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_gt-i8370_galaxy_express

RIFF JTAG – Asus Padfone 2 A68 Unbrick – dead boot repair supported

Posted on by

28.09.2013  RIFF JTAG – Asus Padfone 2 A68  Unbrick – dead boot repair supported

Repairing bricked Asus Padfone A68 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.

To resurrect Asus Padfone A68:

  •  Solder JTAG cable to Asus Padfone A68 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Asus Padfone A68 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

.
asus_padfone2_2

RIFF JTAG – Asus Padfone Infinity A80 Unbrick – dead boot repair supported

Posted on by

28.09.2013  RIFF JTAG – Asus Padfone Infinity A80 Unbrick – dead boot repair supported

Repairing bricked Asus Padfone A80 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.

To resurrect Asus Padfone A80:

  •  Solder JTAG cable to Asus Padfone A80 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Asus Padfone A80 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

.
asus_padfone_infinity_2

RIFF JTAG – HTC T329w (HTC Proto) Unbrick – SuperCID – IMEI repair supported

Posted on by

28.09.2013  RIFF JTAG – HTC T329w (HTC Proto) Unbrick – SuperCID – IMEI repair supported

Repairing bricked HTC Proto (PM6610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.12.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PM661****’.

To resurrect HTC Proto (PM6610000):

  •  Solder JTAG cable to HTC Proto (PM6610000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Proto (PM6610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_x

RIFF JTAG – Samsung Galaxy Ace Duos I589 Unbrick – dead boot repair supported

Posted on by

28.09.2013 RIFF JTAG – Samsung Galaxy Ace Duos I589 Unbrick – dead boot repair supported

Repairing bricked Samsung I589 is easy with the RIFF Box. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung I589 do this:

  •  Solder JTAG cable to Samsung I589 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung I589 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
.
samsung-galaxy-ace-duos-sch-i589-400x365

RIFF JTAG – Samsung SHW-M250S Galaxy S II Unbrick – dead boot repair supported

Posted on by

31.08.2013   RIFF JTAG – Samsung SHW-M250S Galaxy S II Unbrick – dead boot repair supported

Samsung M250S is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung M250S:

  •  Solder JTAG cable to Samsung M250S JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung M250S is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_shw-m250s_galaxy_s_ii

RIFF JTAG – Samsung GT-S7572 Galaxy Trend Duos II Unbrick – Total Repair supported

Posted on by

10.08.2013  RIFF JTAG – Samsung GT-S7572 Galaxy Trend Duos II Unbrick – Total Repair supported

Repairing bricked Samsung S7572 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7572:

  •  Solder JTAG cable to Samsung S7572 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7572 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_trend_duos_2

RIFF JTAG – Samsung GT-N7005 Galaxy Note LTE Unbrick Total Repair supported

Posted on by

10.08.2013   RIFF JTAG – Samsung GT-N7005 Galaxy Note LTE Unbrick Total Repair supported

Repairing bricked Samsung N7005 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung N7005:

  •  Solder JTAG cable to Samsung N7005 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung N7005 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_galaxy_note_3

RIFF JTAG – Samsung GT-i9205 Galaxy Mega 6.3 LT Unbrick – Total Repair supported

Posted on by

10.08.2013  RIFF JTAG – Samsung GT-i9205 Galaxy Mega 6.3 LT Unbrick – Total Repair supported

Repairing bricked Samsung I9205 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
During Resurrection process you can select areas to be resurrected. Select them wisely: selecting everything in one bunch may just increase flashing time while it’s possible that all you need is to repair only few certain areas.

To resurrect Samsung I9205:

  •  Solder JTAG cable to Samsung I9205 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9205 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_galaxy_mega_6.3