Tag Archives: Samsung

RIFF JTAG – Samsung Star Duos (C6712) Unbrick – Boot repair supported

Posted on by

29.11.2011  Samsung Star Duos (C6712) Unbrick – Boot repair supported

Samsung C6712 resurrection is simple. Battery is not required. To power the board it’s most convenient to use an USB Data Cable.
In order to contact to JTAG pads you may need to carefully scratch off paint covering (mask layer) above them. Sometimes there is reset problem with these phones, thus you may need to disconnect and then connect USB cable again.

To resurrect Samsung C6712 do this:

  •  Solder JTAG cable to Samsung C6712 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung C6712 is selected in the list of models
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘SIM Swap’ keys and press Power-On.
__

RIFF JTAG – Unbrick Samsung Galaxy TAB Wi-Fi (P1010), more CDMA Models supported

Posted on by

22.11.2011  Unbrick Samsung Galaxy TAB Wi-Fi (P1010), more CDMA Models supported

Samsung P1010 is based on the OMAP3630 (ARM core is Cortex-A8).

Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
Please note, in most cases you will be required to insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot before starting resurrection. In case you don’t have such card yet, you can create it on the “Samsung P1010 RIFF™ MagicCard” page of the resurrector settings dialog.
This is IRAM version of the Samsung P1010 resurrector. We recommend you using it only in case you had problems connecting to phone with normal Samsung P1010 resurrector DLL.

To resurrect Samsung P1010:

  •  Solder JTAG cable to Samsung P1010 JTAG pads;
  •  Insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P1010 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
There are two DLL-s (Normal and iRAM version) – You can use iRam version in case normal one doesnt work properly. iRam version is much slower, but more robust.
CDMA Models added today :
  • ZTE  AC2766
  • ZTE  AC2746
  • AnyData  ADU555C
Please click “Check for Updates” button in order to download and install new updates.

RIFF JTAG – Samsung i9003 Galaxy SL Unbrick, Boot repair supported

Posted on by

28.10.2011  Samsung i9003 Galaxy SL Unbrick, Boot repair supported

Samsung I9003 is based on the OMAP3630 (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
Please note, in most cases you will be required to insert Samsung I9003 RIFF™ MagicCard into phone’s SD slot before starting resurrection. In case you don’t have such card yet, you can create it on the “Samsung I9003 RIFF™ MagicCard” page of the resurrector settings dialog.
Due to OMAP3630’s some peculiar TrustZone security features current resurrector may fail to boot: if this happens, use Samsung I9003 IRAM resurrector – which works much slower but boots without problems.

To resurrect Samsung I9003:

  •  Solder JTAG cable to Samsung I9003 JTAG pads;
  •  Insert Samsung I9003 RIFF™ MagicCard into phone’s SD slot;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9003 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

RIFF JTAG – Samsung M820 Galaxy Prevail Unbrick, Boot repair supported

Posted on by

28.10.2011  Samsung M820 Galaxy Prevail Unbrick, Boot repair supported

Samsung M820 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung M820 do this:

  •  Solder JTAG cable to Samsung M820 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung M820 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter Download Mode;

RIFF JTAG – Samsung Galaxy S Plus Unbrick, boot repair supported

Posted on by

26.10.2011  Samsung Galaxy S Plus (i9001) Unbrick, boot repair supported

Resurrecting Samsung I9001 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is dual core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.

To resurrect Samsung I9001:

  •  Solder JTAG cable to Samsung I9001 JTAG pads;
  •  Make sure Samsung I9001 is selected in the list of models;
  •  Insert battery and connect USB Data cable;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

RIFF JTAG – Samsung Corby II – S3850 supported

Posted on by

24.10.2011  Samsung Corby II – S3850 supported

Samsung S3850 resurrection is simple. Battery is not required. To power the board it’s most convenient to use an USB Data Cable.
In orger to contact to JTAG pads you may need to carefully scratch off paint covering (mask layer) above them.

To resurrect Samsung S3850 do this:

  •  Solder JTAG cable to Samsung S3850 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung S3850 is selected in the list of models
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Up’ and ‘Call’ keys and press Power-On.

RIFF JTAG – Samsung Z500 supported !

Posted on by

19.10.2011  RIFF JTAG – Samsung Z500 supported !

Resurrection of Samsung Z500 requires battery or external power supply (we didn’t test whether phone is powered on using only a USB cable). You can use RIFF BOX’s 4.2V output for power (requires 1.16 firmware version or later and the 4.2V Output feature enabled in the JTAG Manager).

To resurrect Samsung Z500:

  •  Solder JTAG cable to Samsung Z500 JTAG pads;
  •  Insert battery (or connect external power supply to the battery pads);
  •  Make sure Samsung Z500 is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power-On key shortly;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘9’ key and press ‘Power ON’ button. In few seconds you should see light-blue screen.

RIFF JTAG -Samsung Galaxy II, OMAP4430 version supported (Samsung i9100G, Samsung i9108)

Posted on by

07.10.2011    Samsung Galaxy II, OMAP4430 version supported (Samsung i9100G, Samsung i9108)

Samsung I9108 is based on the OMAP4430 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface. There is a big variety of versions of Galaxy II devices: GT-I9100, GT-I9100G, GT-I9100L, GT-I9100M, GT-I9100T, GT-I9101, GT-I9103, GT-I9108, GT-I9188, and maybe more. Some of them are based on different hardware platform – the Samsung S5PV310 (Cortex-A9 Dual-Core). Thus make sure first which exact hardware version you have on hands.

Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
Current DLL is still a beta one. It will work only with phones which have killed X-Loader.

To resurrect Samsung I9108:

  •  Solder JTAG cable to Samsung I9108 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9108 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

RIFF JTAG -CDMA Samsung F619 supported

Posted on by

07.10.2011    CDMA Samsung F619 supported

The Samsung F619 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung F619:

  •  Solder JTAG cable to Samsung F619 JTAG pads;
  •  Connect USB cable;
  •  Make sure Samsung F619 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘9’ key and press ‘Power ON’ button.