Tag Archives: Samsung

RIFF JTAG – Samsung YP-G70EW Galaxy S WiFi 5.0 Unbrick – Boot repair, World first ! ! !

Posted on by

24.02.2012    Samsung YP-G70EW Galaxy S WiFi 5.0 Unbrick – Boot repair, World first ! ! !

Samsung YP-G70 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.

To resurrect Samsung YP-G70:

  •  Solder JTAG cable to Samsung YP-G70 JTAG pads;
  •  Connect microUSB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung YP-G70 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung GT-P6200 Galaxy Tab 7.0 Plus, ZTE Light Tab (ZTE V9), Orange Boston (Commtiva Z71), Huawei Ideos S7, unbrick – boot repair supported

Posted on by

17.02.2012   Samsung GT-P6200 Galaxy Tab 7.0 Plus, Orange Boston (Commtiva Z71), Huawei Ideos S7, unbrick – boot repair supported

  • Samsung GT-P6200 Galaxy Tab 7.0 Plus 

    Samsung P6200 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
    Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on._
     

  • Huawei Ideos S7Resurrecting Huawei S7 is simple.
    Connection can be established with charger connected while battery is inside. . .
    .

     

  • ZTE Light Tab (ZTE V9)Resurrecting ZTE V9 is easy. Phone is auto powered on with USB Data Cable connected. . .
    _
  • Orange Boston (Commtiva Z71)
    Resurrecting the Orange Boston is easy.  I requires 4.2v external power supply, and some basic soldering skills. . .
    .

To download these new updates, You need to click “Check for Updates” button on Box Service TAB in RIFF JTAG Manager software.

RIFF JTAG – Samsung Galaxy Precedent SCH-M828 Unbrick supported

Posted on by

09.02.2012     Samsung Galaxy Precedent SCH-M828 Unbrick supported

Samsung M828 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung M828 do this:

  •  Solder JTAG cable to Samsung M828 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung M828 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter Download Mode;

_

RIFF JTAG – Samsung GT-i8150 Galaxy W (Samsung Ancora) Unbrick – Boot repair supported

Posted on by

10.01.2012   Samsung GT-i8150 Galaxy W (Samsung Ancora) Unbrick – Boot repair supported

Resurrecting Samsung I8150 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is dual core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.
To resurrect Samsung I8150:

  •  Solder JTAG cable to Samsung I8150 JTAG pads;
  •  Make sure Samsung I8150 is selected in the list of models;
  •  Insert battery and connect USB Data cable;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

_

RIFF JTAG – Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported

Posted on by

10.01.2012     Samsung SGH-T759 Exhibit 4G Unbrick – Boot Repair supported

Samsung T759 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung T759:

  •  Solder JTAG cable to Samsung T759 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Attach battery connector;
  •  Make sure Samsung T759 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

_

RIFF JTAG – Samsung Galaxy Fit (GT-S5670) Unbrick – Boot Repair supported

Posted on by

05.01.2012 Samsung Galaxy Fit (GT-S5670) Unbrick – Boot Repair supported

Samsung S5670 resurrection is simple. Make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5670 do this:

  •  Solder JTAG cable to Samsung S5670 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung S5670 is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power On key on the phone;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;

_

RIFF JTAG – Samsung GT-i9103 Galaxy Z / Galaxy R Boot repair / Unbrick

Posted on by

31.12.2011   A new Year gift ! Samsung GT-i9103 Galaxy Z / Galaxy R (TEGRA2)  Boot repair / Unbrick

Resurrecting Samsung I9103 is easy.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes pressing Power On key during connection may be required. External power supply can be used too.
During some definite startup time (1…3 seconds) TEGRA2 chipsets are not detected via JTAG interface (this could be due to FUSE-d security): that is, on contrary to other devices, which being fused are detected via JTAG but non-haltable, TEGRA2 chipsets give ‘Nothing Detected’ response (though TCK-RTCK pair keeps functioning ok).
Please note: If during resurrection of dead unit the JTAG connection cannot be established (nothing is detected) then re-try with the NRST wire disconnected.

To resurrect Samsung I9103:

  •  Solder JTAG cable to Samsung I9103 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung I9103 is selected in the list of models;
  •  Click Resurrect button;
  •  If nothing is detected then try with NRST wire disconnected;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
_

RIFF JTAG – Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported

Posted on by

29.12.2011      Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported

Samsung I9220 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9220 AP:

  •  Solder JTAG cable to Samsung I9220 AP JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9220 AP is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

_

RIFF JTAG – Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Posted on by

28.12.2011    Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Samsung N7000 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung N7000 AP:

  •  Solder JTAG cable to Samsung N7000 AP JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung N7000 AP is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

_

RIFF JTAG – CDMA Samsung B339 Breeze Supported

Posted on by

23.12.2011 CDMA Samsung B339 Breeze Supported

Resurrecting Samsung B339 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2256

To resurrect Samsung B339:

  •  Solder JTAG cable to Samsung B339 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung B339 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_