Tag Archives: Riff

RIFF JTAG – JTAG Manager v1.31, RIFF Box Firmware v1.23 released

Posted on by

20.04.2011 JTAG Manager v1.31, RIFF Box Firmware v1.23 released

Whats new :

JTAG Manager 1.31

  • “RUN/STOP” Loaders functionality is added (and alternative to the DCC Loaders)

This is required for some ARM7 cores when Debug Communication Channel (DCC) to/from core is not functional (like in MSM6000)

Firmware 1.23

  • Added 8/16/32-bit bus read/write access rotuines for ARM7 core
  • ARM7 debug is now available in ARM/Thumb modes (use the GDBServer for this);

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE Striker (S1602) Boot Repair supported

Posted on by

12.04.2011  CDMA ZTE Striker (S1602) Boot Repair supported

Resurrecting ZTE S1602 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x87FFFF).

To resurrect ZTE S1602:

  • Solder JTAG cable to ZTE S1602 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure ZTE S1602 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA HTC Droid Eris, Unbrick, Boot Repair, ModelID repair supported

Posted on by

12.04.2011   CDMA HTC Droid Eris, Unbrick, Boot Repair, ModelID repair supported

Resurrecting HTC Droid Eris is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB0010000’.

To resurrect HTC Droid Eris:

  • Solder JTAG cable to HTC Droid Eris JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Droid Eris is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
  • Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;

Manual Activation of the phone (in case you see Activation screen and phone is unable to make call to retrieve settings automatically):

  • Press Emergency Call;
  • Dial ##778 and press Call key;
  • Tap “Edit Mode”;
  • Enter password “000000”;
  • Tap NAM Settings;
  • Enter your 10 digit phone number and tap OK;
  • Tap NAM1 and enter your 7 digit cell phone number without area code;
  • Tap NAM2 and enter your 3 digit area code;
  • Tap Back;
  • Tap SID/NID Settings and change the left box to 40 and leave right box as it is and then tap OK;
  • Tap Menu;
  • Tap Commit Mod: after this phone will restart in 10 seconds and will bypass the main activation screen.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported

Posted on by

12.04.2011   HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported

Resurrecting HTC Polaris is easy.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.20.AxeBox. Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘POLA10000’.

To resurrect HTC Polaris:

  • Solder JTAG cable to HTC Polaris JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Polaris selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC 7 Mozart Unbrick, Unlock, IMEI Repair, CID Repair, ModelID Repair supported

Posted on by

09.04.2011    HTC 7 Mozart Unbrick, Unlock, IMEI Repair, CID Repair, ModelID Repair supported

Resurrecting HTC Mozart is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.60.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD6710000’.

To resurrect HTC Mozart:

  • Solder JTAG cable to HTC Mozart JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Mozart is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume Down’ key and press ‘Power ON’ button.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung S7230E Wave 723 Unbrick – Boot Repair supported

Posted on by

08.04.2011 Samsung S7230E Wave 723 Unbrick – Boot Repair supported

Resurrecting Samsung S7230E is easy. To power the phone connect USB cable and insert battery. In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S7230E:

  • Solder JTAG cable to Samsung S7230E JTAG pads;
  • Connect USB cable to phone and PC;
  • Insert battery;
  • Make sure Samsung S7230E is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state. We used MultiLoader 5.64 version.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ (on the left side of phone) and ‘Lock’ (right side bottom part) keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung Galaxy Mini (S5570) Unbrick – Boot repair supported

Posted on by

06.04.2011   Samsung Galaxy Mini (S5570) Unbrick – Boot repair supported

Samsung S5570 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5570 do this:

  • Solder JTAG cable to Samsung S5570 JTAG pads;
  • Insert battery and connect USB cable to phone and PC;
  • Make sure Samsung S5570 is selected in the list of models;
  • Click Resurrect button;
  • Wait few seconds until software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Samsung B159 Boot repair supported

Posted on by

06.04.2011   CDMA Samsung B159 Boot repair supported

Resurrecting Samsung B159 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x57FFFF).

To resurrect Samsung B159:

  • Solder JTAG cable to Samsung B159 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Samsung B159 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA QUALCOMM QSC1100 Generic DLL released

Posted on by

06.04.2011    CDMA QUALCOMM QSC1100 Generic DLL released

Resurrector QSC1100 X14 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU’s internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.

Initial H/W init sequence will setup MCU’s PLL with these parameters:

  • Clock Multiplier = 0x14

Since few different versions of QSC1100 resurrector may exist (with different multiplier values) you may select the one which suits best to your device.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Huawei C2830 Boot repair supported

Posted on by

06.04.2011    CDMA Huawei C2830 Boot repair supported

Resurrecting Huawei C2830 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Since the JTAG test points are placed under keyboard sticker we recommend using USB data cable to supply power to the device.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x5FFFFF).
Please note: if you do not have JIG (that is you solder wires instead) then black graphite covering has to be carefully scratched off in order to access copper surface of the pads.

To resurrect Huawei C2830:

  • Solder JTAG cable to Huawei C2830 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Huawei C2830 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.