Tag Archives: Resurrection

RIFF JTAG – Unlock/IMEI/TA repair – SonyEricsson x8, x10, x10 Mini, x10 mini pro (e15, e10,u20 etc)

Posted on by

11.11.2011    Unlock/IMEI/TA repair –  SonyEricsson x8, x10, x10 Mini, x10 mini pro (e15, e10,u20 etc)

Resurrecting SonyEricsson phones is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.

With current resurrector you can choose Unlock or Resurrection operation to perform. During resurrection, you can select which areas to be repaired. Please note, in some cases phone reports failure during firmware update: in this case you may need to select option to erase Modem SW zone during resurrection.

Example :

During Unlock operation full backup of relevant zones is made, thus you have no risk killing your phone permanently – you have always an option to restore your phone to its original condition with the backup file. Backup files are created in JTAG Manager root directory, in the folder ‘BackupFiles’.

Example :

RIFF JTAG – Samsung i9003 Galaxy SL Unbrick, Boot repair supported

Posted on by

28.10.2011  Samsung i9003 Galaxy SL Unbrick, Boot repair supported

Samsung I9003 is based on the OMAP3630 (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
Please note, in most cases you will be required to insert Samsung I9003 RIFF™ MagicCard into phone’s SD slot before starting resurrection. In case you don’t have such card yet, you can create it on the “Samsung I9003 RIFF™ MagicCard” page of the resurrector settings dialog.
Due to OMAP3630’s some peculiar TrustZone security features current resurrector may fail to boot: if this happens, use Samsung I9003 IRAM resurrector – which works much slower but boots without problems.

To resurrect Samsung I9003:

  •  Solder JTAG cable to Samsung I9003 JTAG pads;
  •  Insert Samsung I9003 RIFF™ MagicCard into phone’s SD slot;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9003 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

RIFF JTAG – Samsung M820 Galaxy Prevail Unbrick, Boot repair supported

Posted on by

28.10.2011  Samsung M820 Galaxy Prevail Unbrick, Boot repair supported

Samsung M820 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung M820 do this:

  •  Solder JTAG cable to Samsung M820 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung M820 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter Download Mode;

RIFF JTAG – HTC Desire CDMA Supported

Posted on by

24.10.2011  HTC Desire CDMA Supported

Resurrecting HTC Desire CDMA is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.60.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PP9940000’.
Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC Desire CDMA:

  •  Solder JTAG cable to HTC Desire CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Back’ key and press ‘Power ON’ button.

RIFF JTAG – HTC Supersonic (EVO 4G) Unbrick, Unlock, IMEI, CID, ModelID repair supported

Posted on by

24.10.2011   HTC Supersonic (EVO 4G) Unbrick, Unlock, IMEI, CID, ModelID repair supported

Resurrecting HTC Supersonic (EVO 4G) is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.16.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC3610000’.
Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code. If selected, then ClockworkMod Recovery v5.0.2.2 will be flashed. Using this recovery you will be able to install zip files from the SD Card, for example you will be able to acquire ROOT rights by installing su-2.3.6.3-efgh-signed.zip file.

To resurrect HTC Supersonic:

  •  Solder JTAG cable to HTC Supersonic JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Supersonic is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

RIFF JTAG – Samsung Corby II – S3850 supported

Posted on by

24.10.2011  Samsung Corby II – S3850 supported

Samsung S3850 resurrection is simple. Battery is not required. To power the board it’s most convenient to use an USB Data Cable.
In orger to contact to JTAG pads you may need to carefully scratch off paint covering (mask layer) above them.

To resurrect Samsung S3850 do this:

  •  Solder JTAG cable to Samsung S3850 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung S3850 is selected in the list of models
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Up’ and ‘Call’ keys and press Power-On.

RIFF JTAG – Samsung Z500 supported !

Posted on by

19.10.2011  RIFF JTAG – Samsung Z500 supported !

Resurrection of Samsung Z500 requires battery or external power supply (we didn’t test whether phone is powered on using only a USB cable). You can use RIFF BOX’s 4.2V output for power (requires 1.16 firmware version or later and the 4.2V Output feature enabled in the JTAG Manager).

To resurrect Samsung Z500:

  •  Solder JTAG cable to Samsung Z500 JTAG pads;
  •  Insert battery (or connect external power supply to the battery pads);
  •  Make sure Samsung Z500 is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power-On key shortly;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘9’ key and press ‘Power ON’ button. In few seconds you should see light-blue screen.

RIFF JTAG – HTC Desire Z (HTC Vision) Unbrick, Unlock, IMEI&CID repair supported

Posted on by

12.10.2011    HTC Desire Z (HTC Vision) Unbrick, Unlock, IMEI&CID repair supported

Resurrecting HTC Desire Z is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Desire Z boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.

Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write one of selected PDA’s SPL versions (0.76.2000 or 0.85.0005). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC1010000’.
There is option to reflash BOOT and RECOVERY zones.

Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Desire Z:

  •  Solder JTAG cable to HTC Desire Z JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Desire Z is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

RIFF JTAG – Samsung i997 infuse 4g Unbrick, Boot repair supported

Posted on by

07.10.2011   Samsung i997 infuse 4g Unbrick, Boot repair supported

Samsung I997 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung I997:

  •  Solder JTAG cable to Samsung I997 JTAG pads;
  •  Connect microUSB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I997 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.