Tag Archives: Resurrection

RIFF JTAG – Huawei E5830 Broadband modem Unbrick – Boot repair supported

Posted on by

12.05.2011  Huawei E5830 Broadband modem Unbrick – Boot repair supported

Resurrecting Huawei E5830 is simple. Just make sure you solder all JTAG signals. Connection can be established with USB Cable connected, though in some rare cases battery presence may be required.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
Please note, if only an USB cable is connected the device is detected by PC as unknown device. So, after resurrection in order to check if modem is alive make sure battery is connected.

To resurrect Huawei E5830:

  • Solder JTAG cable to Huawei E5830 JTAG pads;
  • Insert Huawei E5830 modem into any USB port for power;
  • Make sure Huawei E5830 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

 

RIFF JTAG – CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported

Posted on by

10.05.2011  CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported

Resurrecting LG VM265 is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG VM265:

  • Solder JTAG cable to LG VM265 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure LG VM265 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

 

 

Resurrecting Huawei EC1260 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
At resurrection startup you can select which zones are to be re-flashed. Thus you can save a lot of time if you know approximately which zone is damaged. Select EFS or MMC areas to be flashed only in case you are sure those are damaged – these areas quite big in size; unnecessary reflash is just a waste of time.
Please note, if you chose EFS to be repaired, an original ESN will be lost and substituted with the one contained in resurrection data. Current resurrector does not support ESN repair.

To resurrect Huawei EC1260:

  • Solder JTAG cable to Huawei EC1260 JTAG pads;
  • Insert Huawei EC1260 modem into any USB port for power;
  • Make sure Huawei EC1260 is selected in the list of models;
  • Click Resurrect button;
  • After Selection Dialog popup choose zones to be flashed;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung Nexus S (i9023) Unbrick Boot repair supported

Posted on by

04.05.2011  Samsung Nexus S (i9023) Unbrick Boot repair supported

Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung I9023:

  • Solder JTAG cable to Samsung I9023 JTAG pads;
  • Connect microUSB cable to phone and PC;
  • Insert battery;
  • Make sure Samsung I9023 is selected in the list of models;
  • Make sure a fixed TCK frequency is selected;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported

Posted on by

04.05.2011   HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported

Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000’.

To resurrect HTC Incredible C:

  • Solder JTAG cable to HTC Incredible C JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Incredible C is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
  • Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported

Posted on by

03.05.2011   Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported

Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.

To resurrect Samsung B2710 do this:

  • Solder JTAG cable to the Samsung B2710 JTAG pads;
  • Connect USB cable to phone and PC;
  • Make sure Samsung B2710 is selected in the list of models
  • Click Resurrect button;
  • Wait few seconds until software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘9’ keys and press Power-On. Screen lights up with Download mode message.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC 7 Trophy T8686 (HTC Spark) Unbrick, Unlock, IMEI Repair, CID Update, ModelID Repair supported

Posted on by

22.04.2011   HTC 7 Trophy T8686 (HTC Spark) Unbrick, Unlock, IMEI Repair, CID Update, ModelID Repair supported

Resurrecting HTC Trophy is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.75.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4010000’.

To resurrect HTC Trophy:

  • Solder JTAG cable to HTC Trophy JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Trophy is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume Down’ key and press ‘Power ON’ button.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Motorola W150i (MSM6000) Repair supported

Posted on by

21.04.2011   CDMA Motorola W150i (MSM6000) Repair supported

Resurrecting Motorola W150i is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.

To resurrect Motorola W150i:

  • Solder JTAG cable to Motorola W150i JTAG pads;
  • Connect charger for auto power on or use battery;
  • Make sure Motorola W150i is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported

Posted on by

12.04.2011   HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported

Resurrecting HTC Polaris is easy.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.20.AxeBox. Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘POLA10000’.

To resurrect HTC Polaris:

  • Solder JTAG cable to HTC Polaris JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Polaris selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC 7 Mozart Unbrick, Unlock, IMEI Repair, CID Repair, ModelID Repair supported

Posted on by

09.04.2011    HTC 7 Mozart Unbrick, Unlock, IMEI Repair, CID Repair, ModelID Repair supported

Resurrecting HTC Mozart is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.60.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD6710000’.

To resurrect HTC Mozart:

  • Solder JTAG cable to HTC Mozart JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Mozart is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume Down’ key and press ‘Power ON’ button.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung Galaxy Mini (S5570) Unbrick – Boot repair supported

Posted on by

06.04.2011   Samsung Galaxy Mini (S5570) Unbrick – Boot repair supported

Samsung S5570 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5570 do this:

  • Solder JTAG cable to Samsung S5570 JTAG pads;
  • Insert battery and connect USB cable to phone and PC;
  • Make sure Samsung S5570 is selected in the list of models;
  • Click Resurrect button;
  • Wait few seconds until software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.