Tag Archives: Resurrection

RIFF JTAG – HTC T329w (HTC Proto) Unbrick – SuperCID – IMEI repair supported

Posted on by

28.09.2013  RIFF JTAG – HTC T329w (HTC Proto) Unbrick – SuperCID – IMEI repair supported

Repairing bricked HTC Proto (PM6610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.12.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PM661****’.

To resurrect HTC Proto (PM6610000):

  •  Solder JTAG cable to HTC Proto (PM6610000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Proto (PM6610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_x

RIFF JTAG – NTT DoCoMo Samsung SGH-N055 Galaxy S IV LTE SC-04E Unbrick – dead boot repair supported

Posted on by

31.08.2013  RIFF JTAG – NTT DoCoMo Samsung SGH-N055 Galaxy S IV LTE SC-04E Unbrick – dead boot repair supported

Repairing bricked Samsung SC-04E is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0x42 error during connection stage.
During Resurrection process you can select areas to be resurrected. Select them wisely: selecting everything in one bunch may just increase flashing time while it’s possible that all you need is to repair only few certain areas.

To resurrect Samsung SC-04E:

  •  Solder JTAG cable to Samsung SC-04E JTAG pads;
  •  Connect USB cable or insert battery;
  •  Make sure Samsung SC-04E is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
s4-jap

RIFF JTAG – Samsung GT-i9205 Galaxy Mega 6.3 LT Unbrick – Total Repair supported

Posted on by

10.08.2013  RIFF JTAG – Samsung GT-i9205 Galaxy Mega 6.3 LT Unbrick – Total Repair supported

Repairing bricked Samsung I9205 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
During Resurrection process you can select areas to be resurrected. Select them wisely: selecting everything in one bunch may just increase flashing time while it’s possible that all you need is to repair only few certain areas.

To resurrect Samsung I9205:

  •  Solder JTAG cable to Samsung I9205 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9205 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_galaxy_mega_6.3

RIFF JTAG – Samsung SCH-i545 Galaxy S4 (Samsung Altius) Unbrick – Total Repair supported

Posted on by

10.08.2013  RIFF JTAG – Samsung SCH-i545 Galaxy S4 (Samsung Altius) Unbrick – Total Repair supported

Repairing bricked Samsung I545 is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0x42 error during connection stage.
During Resurrection process you can select areas to be resurrected. Select them wisely: selecting everything in one bunch may just increase flashing time while it’s possible that all you need is to repair only few certain areas.

To resurrect Samsung I545:

  •  Solder JTAG cable to Samsung I545 JTAG pads;
  •  Connect USB cable or insert battery;
  •  Make sure Samsung I545 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
samsung_sch-545_galaxy_s4

RIFF JTAG – Samsung SGH-i337M Galaxy S 4 LTE 32GB (Samsung Altius) Unbrick Total Repair supported

Posted on by

10.08.2013  RIFF JTAG – Samsung SGH-i337M Galaxy S 4 LTE 32GB (Samsung Altius) Unbrick Total Repair supported

Repairing bricked Samsung I337M is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Please note, battery must be charged. If battery is not charged enough there is chance of getting 0x42 error during connection stage.
During Resurrection process you can select areas to be resurrected. Select them wisely: selecting everything in one bunch may just increase flashing time while it’s possible that all you need is to repair only few certain areas.

To resurrect Samsung I337M:

  •  Solder JTAG cable to Samsung I337M JTAG pads;
  •  Connect USB cable or insert battery;
  •  Make sure Samsung I337M is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
samsung_galaxy_s_4_4

RIFF JTAG – HTC One LTE 32GB (HTC M7) Unbrick, Unlock, IMEI and SuperCID supported

Posted on by

27.06.2013   RIFF JTAG – HTC One LTE 32GB (HTC M7) Unbrick, Unlock, IMEI and SuperCID supported

Repairing bricked HTC OneM7 (PN0710000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.44.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PN0710000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneM7 (PN0710000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneM7 (PN0710000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_3

RIFF JTAG – HTC One VX (HTC Totem C2) Supported

Posted on by

03.06.2013  RIFF JTAG – HTC One VX (HTC Totem C2) Supported

Repairing bricked HTC OneVX (PM3610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.31.0013 version. Additionally to SPL and Radio zOneVX, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM3610000’.

To resurrect HTC OneVX:

  •  Solder JTAG cable to HTC OneVX JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneVX (PM3610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_vx

RIFF JTAG – HTC Desire SV T326e (HTC Magni) Unbrick – Dead boot repair supported

Posted on by

27.05.2013  RIFF JTAG – HTC Desire SV T326e (HTC Magni) Unbrick – Dead boot repair supported

Repairing bricked HTC Desire SV (PM8610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.35.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PM8610000’.

To resurrect HTC Desire SV (PM8610000):

  •  Solder JTAG cable to HTC Desire SV (PM8610000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire SV (PM8610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_sv_3

RIFF JTAG – HTC J ISW13HT (HTC Valente) Unbrick – Dead boot repair supported

Posted on by

27.05.2013  RIFF JTAG – HTC J ISW13HT (HTC Valente) Unbrick – Dead boot repair supported

Repairing bricked HTC Valente (PK0710000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK0710000’.

To resurrect HTC Valente (PK0710000):

  •  Solder JTAG cable to HTC Valente (PK0710000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Valente (PK0710000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htcj

RIFF JTAG – HTC Desire VC T328d Unbrick – dead boot repair supported

Posted on by

09.05.2013  RIFF JTAG – HTC Desire VC T328d Unbrick – dead boot repair supported

Repairing bricked HTC DesireVC (PK7810000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.27.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK7810000’.

To resurrect HTC DesireVC (PK7810000):

  •  Solder JTAG cable to HTC DesireVC (PK7810000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC DesireVC (PK7810000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_vc_t328d_2