Tag Archives: Presence

RIFF JTAG – CDMA Samsung SCH-S109 (MSM6000) Repair supported

Posted on by

20.04.2011  CDMA Samsung SCH-S109 (MSM6000) Repair supported

Resurrecting Samsung S109 is simple. Phone is auto powered on with charger connected; battery presence is not required.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x3FFFFF).

To resurrect Samsung S109:

  • Solder JTAG cable to Samsung S109 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Samsung S109 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE Striker (S1602) Boot Repair supported

Posted on by

12.04.2011  CDMA ZTE Striker (S1602) Boot Repair supported

Resurrecting ZTE S1602 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x87FFFF).

To resurrect ZTE S1602:

  • Solder JTAG cable to ZTE S1602 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure ZTE S1602 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Huawei C2830 Boot repair supported

Posted on by

06.04.2011    CDMA Huawei C2830 Boot repair supported

Resurrecting Huawei C2830 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Since the JTAG test points are placed under keyboard sticker we recommend using USB data cable to supply power to the device.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x5FFFFF).
Please note: if you do not have JIG (that is you solder wires instead) then black graphite covering has to be carefully scratched off in order to access copper surface of the pads.

To resurrect Huawei C2830:

  • Solder JTAG cable to Huawei C2830 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Huawei C2830 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – RoverPC EVO V7 Unbrick – Dead boot repair supported

Posted on by

21.03.2011  RoverPC EVO V7 Unbrick – Dead boot repair supported

RoverPC Evo V7 resurrection is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect RoverPC Evo V7:

  • Solder JTAG cable to RoverPC Evo V7 JTAG pads;
  • Connect USB cable to phone and PC;
  • Make sure RoverPC Evo V7 is selected in the list of models;
  • Make sure a fixed TCK frequency is selected;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original firmware downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung SGH-i607 BlackJack PDA Unbrick, Dead Boot repair supported

Posted on by

12.03.2011  Samsung SGH-i607 BlackJack PDA Unbrick, Dead Boot repair supported

Resurrecting Samsung i607 PDA part is easy. Phone requires battery presence in order to establish JTAG connection. If you additionally connect charger the phone will be auto powered on and there will be no need to press Power on key.
In case you experience connection problems, de-power phone completely, disconnect charger (if it was used), then insert battery, click Resurrection button in the JTAG Manger and immediately (within 0…1 seconds) press Power On key.

To unbrick Samsung i607 PDA part:

  • Solder JTAG cable to Samsung i607 PDA JTAG pads;
  • Make sure Samsung i607 PDA is selected in the list of models;
  • If only battery is connected – press Power On key shortly;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Huawei C5005 Unbrick – Repair supported

Posted on by

11.03.2011  CDMA Huawei C5005 Unbrick – Repair supported

Resurrecting Huawei C5005 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0xBFFFFF).

To resurrect Huawei C5005:

  • Solder JTAG cable to Huawei C5005 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Huawei C5005 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE F285 Repair supported

Posted on by

10.03.2011 CDMA ZTE F285 Repair supported

Resurrecting ZTE F285 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x60FFFF).
To resurrect ZTE F285:

  • Solder JTAG cable to ZTE F285 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure ZTE F285 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.