Tag Archives: Presence

RIFF JTAG – LG CU720 Shine Unbrick – Boot repair supported

Posted on by

07.05.2011  LG CU720 Shine Unbrick – Boot repair supported

Resurrecting LG CU720 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG CU720:

  • Solder JTAG cable to LG CU720 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure LG CU720 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.Đ

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported

Posted on by

04.05.2011   HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported

Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000’.

To resurrect HTC Incredible C:

  • Solder JTAG cable to HTC Incredible C JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Incredible C is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
  • Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Samsung S239 (MPower) Repair supported

Posted on by

26.04.2011  CDMA Samsung S239 (MPower) Repair supported

Resurrecting Samsung S239 is simple. Phone is auto powered on with USB Cable connected; battery presence is not required.

To resurrect Samsung S239:

  • Solder JTAG cable to Samsung S239 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Samsung S239 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE C370 Repair supported

Posted on by

22.04.2011  CDMA ZTE C370 Repair supported

Resurrecting ZTE C370 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0098/0x0096

To resurrect ZTE C370:

  • Solder JTAG cable to ZTE C370 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure ZTE C370 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C6000 Repair supported

Posted on by

22.04.2011   CDMA Haier C6000 Repair supported

Resurrecting Haier C6000 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0x2210

To resurrect Haier C6000:

  • Solder JTAG cable to Haier C6000 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C6000 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C5100 Repair supported

Posted on by

22.04.2011  CDMA Haier C5100 Repair supported

Resurrecting Haier C5100 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C5100:

  • Solder JTAG cable to Haier C5100 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C5100 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C2040 Repair supported

Posted on by

22.04.2011  CDMA Haier C2040 Repair supported

Resurrecting Haier C2040 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C2040:

  • Solder JTAG cable to Haier C2040 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C2040 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C3010, LG LSP450T Repair supported

Posted on by

22.04.2011  CDMA Haier C3010, LG LSP450T Repair supported

Resurrecting Haier C3010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chips with IDs 0x00EC/0x257E and 0x017E/0x2210. Proper data will be selected automatically depending on memory ID in your device.

To resurrect Haier C3010:

  • Solder JTAG cable to Haier C3010 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C3010 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Resurrecting LG LSP450T is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0020/0x8867

To resurrect LG LSP450T:

  • Solder JTAG cable to LG LSP450T JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure LG LSP450T is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C300 Repair supported

Posted on by

21.04.2011  CDMA Haier C300 Repair supported

Resurrecting Haier C300 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Haier C300:

  • Solder JTAG cable to Haier C300 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C300 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Motorola W150i (MSM6000) Repair supported

Posted on by

21.04.2011   CDMA Motorola W150i (MSM6000) Repair supported

Resurrecting Motorola W150i is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.

To resurrect Motorola W150i:

  • Solder JTAG cable to Motorola W150i JTAG pads;
  • Connect charger for auto power on or use battery;
  • Make sure Motorola W150i is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.