Tag Archives: Power Supply

RIFF JTAG – Samsung GT-S6012 Galaxy Music Duos Unbrick – Dead Boot repair supported

Posted on by

29.12.2012  RIFF JTAG – Samsung GT-S6012 Galaxy Music Duos Unbrick – Dead Boot repair supported

Repairing bricked Samsung S6012 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S6012:

  •  Solder JTAG cable to Samsung S6012 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S6012 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘OK’ keys and press Power-On. And after you see the warning message press ‘Volume Up’ key to enter Download Mode.

.
samsung_galaxy_music

RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

29.12.2012  RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC OneS (PJ4010000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.06.0000 or 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4010000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS PJ4010000 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_s

RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

Posted on by

29.12.2012  RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

Repairing bricked HTC ChaCha (HTC Status) (PH0613000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH0613000’.

To resurrect HTC ChaCha:

  •  Solder JTAG cable to HTC ChaCha (PH0613000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC ChaCha (PH0613000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_status

RIFF JTAG – ZTE F160 Unbrick – Dead Boot repair supported

Posted on by

29.12.2012  RIFF JTAG – ZTE F160 Unbrick – Dead Boot repair supported

Repairing bricked ZTE F160 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected.

To resurrect ZTE F160:

  •  Solder JTAG cable to ZTE F160 JTAG pads;
  •  Make sure ZTE F160 is selected in the list of models;
  •  Connect USB Data Cable;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

zte_f160

RIFF JTAG – HTC HD Mini T5555 (HTC Photon) Unbrick, Unlock, IMEI, CID repair supported

Posted on by

29.11.2012 RIFF JTAG – HTC HD Mini T5555 (HTC Photon) Unbrick, Unlock, IMEI, CID repair supported

Repairing bricked HTC HD Mini is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB9210000’.
Currently supported resurrection for NAND memories with 2KB page size.

To resurrect HTC HD Mini:

  •  Solder JTAG cable to HTC HD Mini JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC HD Mini is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Sensation PG5811000 Unbrick, Unlock, IMEI, CID repair supported

Posted on by

27.11.2012  RIFF JTAG – HTC Sensation PG5811000 Unbrick, Unlock, IMEI, CID repair supported

Repairing bricked HTC Sensation (PG5811000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 1.21.0001. Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG5811000’.

There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC Sensation (PG5811000):

  •  Solder JTAG cable to HTC Sensation (PG5811000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Sensation (PG5811000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung SGH-Z710 Unbrick – Dead Boot Repair Supported

Posted on by

23.11.2012   RIFF JTAG – Samsung SGH-Z710 Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung Z710 is easy with the RIFF Box.

To resurrect Samsung Z710:

  •  Solder JTAG cable to Samsung Z710 JTAG pads;
  •  Connect USB cable or instert batteryu;
  •  Make sure Samsung Z710 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘9’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Posted on by

21.11.2012  RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Repairing bricked HTC OneS is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.09.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4020000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung Gravity 3 SGH-T479 Unbrick – Dead Boot Repair Supported

Posted on by

20.11.2012  RIFF JTAG – Samsung Gravity 3 SGH-T479 Unbrick – Dead Boot Repair Supported

The Samsung T479 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung T479:

  •  Solder JTAG cable to Samsung T479 JTAG pads;
  •  Connect USB cable;
  •  Make sure Samsung T479 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.

.

RIFF JTAG – HTC Amaze 4G (HTC Ruby) Unbrick – Dead Boot Repair Supported

Posted on by

20.11.2012  RIFF JTAG – HTC Amaze 4G (HTC Ruby) Unbrick – Dead Boot Repair Supported

Repairing bricked HTC Amaze4G is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 1.90.0008. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH8511000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC Amaze4G:

  •  Solder JTAG cable to HTC Amaze4G JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Amaze4G is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.