Tag Archives: Power Supply

RIFF JTAG – HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported

Posted on by

31.03.2011    HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported

Resurrecting HTC Chief is easy:
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.44.0000 SPL version.
Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘CEDA10000’.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.

To resurrect HTC Chief:

  • Solder JTAG cable to HTC Chief JTAG pads;
  • Make sure HTC Chief is selected in the list of models;
  • Insert battery and connect USB Cable;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung SGH-i607 BlackJack PDA Unbrick, Dead Boot repair supported

Posted on by

12.03.2011  Samsung SGH-i607 BlackJack PDA Unbrick, Dead Boot repair supported

Resurrecting Samsung i607 PDA part is easy. Phone requires battery presence in order to establish JTAG connection. If you additionally connect charger the phone will be auto powered on and there will be no need to press Power on key.
In case you experience connection problems, de-power phone completely, disconnect charger (if it was used), then insert battery, click Resurrection button in the JTAG Manger and immediately (within 0…1 seconds) press Power On key.

To unbrick Samsung i607 PDA part:

  • Solder JTAG cable to Samsung i607 PDA JTAG pads;
  • Make sure Samsung i607 PDA is selected in the list of models;
  • If only battery is connected – press Power On key shortly;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Tattoo A3232 (HTC Click 1100) Unlock, Unbrick, IMEI repair, CID Update

Posted on by

10.03.2011 HTC Tattoo A3232 (HTC Click 1100) Unlock, Unbrick, IMEI repair, CID Update supported

Resurrecting HTC Click is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside.
There are two different hardware versions exist – one based on the MSM7225 chipset (CLIC10000) and other – on the ESM7225 chipset (CLIC11000). In resurrector settings you can select a desired version.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.52.0001 SPL version.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.

To resurrect HTC Click:

  • Solder JTAG cable to HTC Click JTAG pads;
  • Make sure HTC Click is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To Unlock HTC Click :

  • Solder JTAG cable to HTC Click JTAG pads;
  • Make sure HTC Click is selected in the list of models;
  • Click Resurrect button;
  • Select “Unlock Settings” TAB
  • Select Unlock method
  • Click “Unlock”

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – JTAG Manager v1.20, RIFF Box firmware v1.16 released

Posted on by

16.12.2010  JTAG Manager v1.20, RIFF Box firmware v1.16 released

Whats new :

JTAG Manager 1.20

– added 4.2V power supply output (RIFF RJ45 pin 1) controlling feature
For this go to DCC Read/Write page, click “Notifications…”, the Notifications dialog will be displayed,
go to “For Advanced Users” page and set desired mode for “Enable 4.2V output” checkbox.
When enabled, 4.2V line will be powered on after any “JTAG” operation executed and will remain “ON” until
box restart or until “Enable 4.2V output” checkbox is unchecked and any “JTAG” operation is executed.
– (SDK): exported new SUB_ID_GET_ROM_INFO function for resurrectors;

Firmware 1.16

– code is optimized to avoid deadlocks in ARM11 handling routines;
– reset sequence (after NRST assertion) is optimized for ARM11 core;
– added 4.2V power supply output (RIFF RJ45 pin 1) controlling feature

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new files, download it and restart the software.