Tag Archives: Power Supply

RIFF JTAG – HTC Sensation XL X315 / Bass (HTC Runnymede) Unbrick, Unlock, IMEI and CID update supported

Posted on by

21.03.2012    RIFF JTAG – HTC Sensation XL X315 / Bass (HTC Runnymede) Unbrick, Unlock, IMEI and CID update supported

Repairing bricked  HTC SensationXL (PI39200) is easy using RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC SensationXL boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to 1.25.0004 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG3920000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC SensationXL:

  •  Solder JTAG cable to HTC SensationXL JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC SensationXL is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC EVO View 4G Unbrick, Unlock, IMEI and CID update supported

Posted on by

19.03.2012    RIFF JTAG – HTC EVO View 4G Unbrick, Unlock, IMEI and CID update supported

Repairing bricked HTC EvoView4G is easy using RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC EvoView4G boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to 1.38.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG4120000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC EvoView4G:

  •  Solder JTAG cable to HTC EvoView4G JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC EvoView4G is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC EVO 3D (HTC Shooter) Unbrick – Boot Repair Supported, World First ! ! !

Posted on by

14.03.2012   RIFF JTAG – HTC EVO 3D  (HTC Shooter) Unbrick – Boot Repair Supported, World First  ! ! !

Repairing bricked HTC EVO 3D (PG86300) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.49.0007. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG8630000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC EVO 3D:

  •  Solder JTAG cable to HTC EVO 3D JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC EVO 3D is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Sensation (HTC Pyramid) Unbrick, ModelID, CID, IMEI repair Supported

Posted on by

14.03.2012   RIFF JTAG – HTC Sensation  (HTC Pyramid)  Unbrick, ModelID, CID, IMEI repair Supported

Repairing bricked HTC Sensation is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.

Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.18.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG5813000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC Sensation:

  •  Solder JTAG cable to HTC Sensation JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Sensation is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – LG P350 Pecan / Optimus Me Unbrick – Boot Repair supported

Posted on by

12.03.2012   RIFF JTAG – LG P350 Pecan / Optimus Me Unbrick – Boot Repair supported

Resurrecting LG P350 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG P350:

  •  Solder JTAG cable to LG P350 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG P350 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods. We used KDZ_FW_UPD update software (with settings Type = 3GQCP, PhoneMode = EMERGENCY) to flash the *.KDZ firmware into phone.

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button. In few seconds you should see emergency mode screen saying “DOWNLOAD MODE”.

.

RIFF JTAG – Samsung Wave 3 GT-S8600 Unbrick – Boot repair supported, World First ! ! !

Posted on by

29.02.2012    Samsung Wave 3 GT-S8600 Unbrick – Boot repair supported, World First !  !  !

Resurrecting Samsung S8600 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is dual core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.

To resurrect Samsung S8600:

  •  Solder JTAG cable to Samsung S8600 JTAG pads;
  •  Make sure Samsung S8600 is selected in the list of models;
  •  Insert battery and connect USB Data cable;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Menu’ keys and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-S7500 Galaxy Ace Plus Unbrick – Boot Repair supported, World First ! ! !

Posted on by

28.02.2012      Samsung GT-S7500 Galaxy Ace Plus Unbrick – Boot Repair supported, World First !  !  !

Resurrecting Samsung S7500 is easy.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7500:

  •  Solder JTAG cable to Samsung S7500 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7500 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported

Posted on by

14.02.2012     HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported

Resurrecting HTC Thunderbolt CP (Modem Part) part is easy.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes during connection pressing Power On key may be required.
Please note, CP Part’s power is controlled by the AP Part, thus you may experience constant connection loses after definite ammounts of time (1-2-5-x seconds). If this keeps interferring the resurrection process, solder additionall JTAG interface cable to the AP pads, select AP resurrector DLL, go to the JTAG Read/Write page and halt AP core, then switch back to the CP JTAG interface.

To resurrect HTC Thunderbolt CP (Modem Part) Part:

  •  Solder JTAG cable to HTC Thunderbolt CP JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Thunderbolt CP is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Resurrecting HTC Thunderbolt AP (PDA Part) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.04.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG0510000’.
There is option to reflash BOOT and RECOVERY zones.

_

RIFF JTAG – HTC Droid Incredible 2 ADR6350 Boot repair, Unlock, CID, ModelID, IMEI Update

Posted on by

HTC Droid Incredible 2 ADR6350 Boot repair, Unlock, CID, ModelID, IMEI Update

Resurrecting HTC Incredible 2 (Droid Incredible 2 ADR6350VW) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Incredible 2 boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8655 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 6.13.1002. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG3210***’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Incredible 2:

  •  Solder JTAG cable to HTC Incredible 2 JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Incredible 2 is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

_

RIFF JTAG – HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported

Posted on by

HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported

Resurrecting HTC Glacier is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Glacier boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write SPL version 0.86.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD1510000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Glacier:

  •  Solder JTAG cable to HTC Glacier JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Glacier is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

    _