Tag Archives: Pc Cable

RIFF JTAG – HTC One X AT&T Unbrick, IMEI, SuperCID repair supported

Posted on by

30.01.2013 RIFF JTAG – HTC One X AT&T(PJ8310000) Unbrick, IMEI, SuperCID repair supported

Repairing bricked HTC OneX (PJ8310000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8310000’.

To resurrect HTC OneX (PJ8310000):

  •  Solder JTAG cable to HTC OneX (PJ8310000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneX (PJ8310000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_x

RIFF JTAG – LG E900 Optimus 7 Unbrick – Dead Boot repair supported

Posted on by

26.01.2013  RIFF JTAG – LG E900 Optimus 7 Unbrick – Dead Boot repair supported

Repairing bricked LG E900 with the RIFF Box requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E900:

  •  Solder JTAG cable to LG E900 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E900 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume down’ and ‘Camera’ keys and press ‘Power ON’ button.

.
lg_e900_optimus_7_2

RIFF JTAG – Samsung GT-P5100 Galaxy Tab 2 10.1 Unbrick – Dead Boot repair supported

Posted on by

26.01.2013   RIFF JTAG – Samsung GT-P5100 Galaxy Tab 2 10.1 Unbrick – Dead Boot repair supported

Samsung P5100 is based on the OMAP4430 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Please note: The initial loader in the Samsung P5100 is XLOADER. Due to OMAP4430’s some peculiar TrustZone security features current resurrector will boot only in case XLOADER is alive. That’s why model name of current resurrector has additional text: ‘XLoader+’. In case XLOADER is damaged (which happens for example after wrong firmware reflash), you will have to use different resurrector DLL – the one with the ‘XLoader-” delimiter.

To resurrect Samsung P5100:

  •  Solder JTAG cable to Samsung P5100 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P5100 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_galaxy_tab2_101

RIFF JTAG – Samsung GT-P5110 Galaxy Tab 2 10.1 WiFi Unbrick – Dead Boot repair supported

Posted on by

25.01.2013 RIFF JTAG – Samsung GT-P5110 Galaxy Tab 2 10.1 WiFi Unbrick – Dead Boot repair supported

Samsung P5110 is based on the OMAP4430 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Please note: The initial loader in the Samsung P5110 is XLOADER. Due to OMAP4430’s some peculiar TrustZone security features current resurrector will boot only in case XLOADER is alive. That’s why model name of current resurrector has additional text: ‘XLoader+’. In case XLOADER is damaged (which happens for example after wrong firmware reflash), you will have to use different resurrector DLL – the one with the ‘XLoader-” delimiter.

To resurrect Samsung P5110:

  •  Solder JTAG cable to Samsung P5110 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P5110 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_galaxy_tab2_101

RIFF JTAG – Samsung GT-S7562 Galaxy S Duos Unbrick – Dead Boot repair supported

Posted on by

22.01.2013   RIFF JTAG – Samsung GT-S7562 Galaxy S Duos Unbrick – Dead Boot repair supported

Repairing bricked Samsung S7562 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7562:

  •  Solder JTAG cable to Samsung S7562 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7562 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_s_duos_front

RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

Posted on by

15.01.2013 RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

Repairing bricked HTC DesireV (PL1110000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.14.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PL1110000’.

To resurrect HTC DesireV (PL1110000):

  •  Solder JTAG cable to HTC DesireV (PL1110000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC DesireV (PL1110000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_v_t328w_2

RIFF JTAG – Samsung SGH-T879 Galaxy Note Unbrick – Dead Boot repair supported

Posted on by

29.12.2012  RIFF JTAG – Samsung SGH-T879 Galaxy Note Unbrick – Dead Boot repair supported

Repairing bricked Samsung T879 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung T879:

  •  Solder JTAG cable to Samsung T879 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung T879 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
t-mobile-galaxy-note

RIFF JTAG – Samsung GT-S7562i Galaxy S Duos Unbrick – Dead Boot repair supported

Posted on by

29.12.2012  RIFF JTAG – Samsung GT-S7562i Galaxy S Duos Unbrick – Dead Boot repair supported

Repairing bricked Samsung S7562I is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7562I:

  •  Solder JTAG cable to Samsung S7562I JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7562I is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_s_duos

RIFF JTAG – Samsung GT-S7530 Omnia M Unbrick – Dead Boot repair supported

Posted on by

29.12.2012  RIFF JTAG – Samsung GT-S7530 Omnia M Unbrick – Dead Boot repair supported

Repairing bricked Samsung S7530 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7530:

  •  Solder JTAG cable to Samsung S7530 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7530 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Up’ and ‘Camera’ keys and press Power-On.

.
samsung_omnia_m

RIFF JTAG – Samsung GT-S6012 Galaxy Music Duos Unbrick – Dead Boot repair supported

Posted on by

29.12.2012  RIFF JTAG – Samsung GT-S6012 Galaxy Music Duos Unbrick – Dead Boot repair supported

Repairing bricked Samsung S6012 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S6012:

  •  Solder JTAG cable to Samsung S6012 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S6012 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘OK’ keys and press Power-On. And after you see the warning message press ‘Volume Up’ key to enter Download Mode.

.
samsung_galaxy_music