Tag Archives: Pc Cable

RIFF JTAG – Samsung GT-i8530 Galaxy Beam Unbrick – Dead Boot Repair Supported

Posted on by

16.11.2012 RIFF JTAG – Samsung GT-i8530 Galaxy Beam Unbrick – Dead Boot Repair SupportedĐ

Repairing bricked Samsung I8530 is easy with the RIFF Box.
Please note, if you have problems connecting phone, then make sure USB Cable is disconnected, insert battery and press Power On and try connecting again.

To resurrect Samsung I8530:

  •  Solder JTAG cable to Samsung I8530 JTAG pads;
  •  Attach battery;
  •  Disconnect USB Cable (if was connected);
  •  Make sure Samsung I8530 is selected in the list of models;
  •  Click Resurrect button;
  •  If required, press Power On key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – LG E610/E612 Optimus L5 Unbrick -Dead Boot Repair Supported

Posted on by

16.11.2012   RIFF JTAG – LG E610/E612 Optimus L5 Unbrick -Dead Boot Repair Supported

Repairing bricked LG E612 is easy with the RIFF Box. 
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E612:

  •  Solder JTAG cable to LG E612 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E612 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-i8350 Omnia W Unbrick – Dead Boot Repair Supported

Posted on by

14.11.2012   RIFF JTAG – Samsung GT-i8350 Omnia W Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung I8350 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.

To resurrect Samsung I8350:

  •  Solder JTAG cable to Samsung I8350 JTAG pads;
  •  Make sure Samsung I8350 is selected in the list of models;
  •  Insert battery and connect USB Data cable;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-P7320 Galaxy Tab 8.9 LTE Unbrick – Dead Boot Repair Supported

Posted on by

13.11.2012  RIFF JTAG – Samsung GT-P7320 Galaxy Tab 8.9 LTE Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung P7320 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung P7320:

  •  Solder JTAG cable to Samsung P7320 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P7320 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Up’ key (which is closest to Power-On key) and press Power-On.

.

RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Posted on by

13.11.2012 RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Resurrecting HTC WildFireS CDMA is easy with RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 (for NAND chips with 4Kb page size). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG7620000’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS CDMA:

  •  Solder JTAG cable to HTC WildFireS CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC WildFireS CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

.

RIFF JTAG – HTC Flyer 4G P515E Unbrick, IMEI, SuperCID, ModelID repair supported

Posted on by

02.11.2012   RIFF JTAG – HTC Flyer 4G P515E Unbrick, IMEI, SuperCID, ModelID repair supported

Repairing bricked HTC Flyer4G (PG4130000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Flyer4G (PG4130000) boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so if DBL area is damanged and MCU has JTAG Disable FUSE blown then there is no way to resurrect your phone via JTAG interface. However, in this case you may use HTC Flyer4G (PG4130000) USB DLL version which does not require JTAG interface and does resurrection procedure via USB cable.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL to 1.14.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG413****’.

To resurrect HTC Flyer:

  •  Solder JTAG cable to HTC Flyer JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Flyer4G (PG4130000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-S6802 Galaxy Ace Duos Unbrick – Dead Boot Repair Supported

Posted on by

02.11.2012   RIFF JTAG – Samsung GT-S6802 Galaxy Ace Duos Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung S6802 is easy with the RIFF Box. Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S6802:

  •  Solder JTAG cable to Samsung S6802 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S6802 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung GT-S5830L Galaxy Ace Unbrick – Dead Boot Repair Supported

Posted on by

19.10.2012   RIFF JTAG – Samsung GT-S5830L Galaxy Ace Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung S5830L is easy with the RIFF Box. You need to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5830L do this:

  •  Solder JTAG cable to Samsung S5830L JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung S5830L is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power On button shortly if it stops on establish conneciton stage;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

.

RIFF JTAG – Samsung GT-S5300 Galaxy Pocket Unbrick – Dead Boot Repair Supported

Posted on by

19.10.2012  RIFF JTAG – Samsung GT-S5300 Galaxy Pocket Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung S5300 is easy with the RIFF Box. Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S5300:

  •  Solder JTAG cable to Samsung S5300 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S5300 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung GT-i9070 Galaxy S Advance Unbrick – Dead Boot Repair Supported

Posted on by

18.10.2012  RIFF JTAG – Samsung GT-i9070 Galaxy S Advance Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung I9070 is easy with the RIFF Box.
Please note, if you have problems connecting phone, then make sure USB Cable is disconnected, insert battery and press Power On and try connecting again.

To resurrect Samsung I9070:

  •  Solder JTAG cable to Samsung I9070 JTAG pads;
  •  Attach battery;
  •  Disconnect USB Cable (if was connected);
  •  Make sure Samsung I9070 is selected in the list of models;
  •  Click Resurrect button;
  •  If required, press Power On key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.