Tag Archives: Pc Battery

RIFF JTAG – HTC Desire C NFC A320e (HTC Golf) Unbrick, Unlock, SuperCID, IMEI repair supported

Posted on by

20.02.2013 RIFF JTAG – HTC Desire C NFC A320e (HTC Golf) Unbrick, Unlock, SuperCID, IMEI repair supported

Repairing bricked HTC Desire C (PL0110000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.25.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PL0110000’.

To resurrect HTC Desire C (PL0110000):

  •  Solder JTAG cable to HTC Desire C (PL0110000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire C (PL0110000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_c

RIFF JTAG – HTC Desire X (HTC Proto) Unbrick , Unlock, SuperCID and IMEI repair supported

Posted on by

14.02.2013    RIFF JTAG – HTC Desire X (HTC Proto) Unbrick , Unlock, SuperCID and IMEI repair supported

Repairing bricked HTC Desire X (PM6610000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.24.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PM6610000’.

To resurrect HTC Desire X (PM6610000):

  •  Solder JTAG cable to HTC Desire X (PM6610000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire X (PM6610000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_x_2

RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

Posted on by

09.02.2013   RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

Repairing bricked HTC OneXL (PJ8312000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8312000’.

To resurrect HTC OneXL (PJ8312000):

  •  Solder JTAG cable to HTC OneXL (PJ8312000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneXL (PJ8312000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_xl

RIFF JTAG – HTC Droid DNA ADR6435 / Droid Incredible X (HTC DLX) Unbrick, Unlock, IMEI and SuperCID repair supported

Posted on by

RIFF JTAG – HTC Droid DNA ADR6435 / Droid Incredible X (HTC DLX) Unbrick, Unlock, IMEI and SuperCID repair supported

Repairing bricked HTC Droid DNA (PL8320000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.33.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PL8320000’.

To resurrect HTC Droid DNA (PL8320000):

  •  Solder JTAG cable to HTC Droid DNA (PL8320000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Droid DNA (PL8320000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_droid_dna

RIFF JTAG – HTC One X AT&T Unbrick, IMEI, SuperCID repair supported

Posted on by

30.01.2013 RIFF JTAG – HTC One X AT&T(PJ8310000) Unbrick, IMEI, SuperCID repair supported

Repairing bricked HTC OneX (PJ8310000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8310000’.

To resurrect HTC OneX (PJ8310000):

  •  Solder JTAG cable to HTC OneX (PJ8310000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneX (PJ8310000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_x

RIFF JTAG – LG E900 Optimus 7 Unbrick – Dead Boot repair supported

Posted on by

26.01.2013  RIFF JTAG – LG E900 Optimus 7 Unbrick – Dead Boot repair supported

Repairing bricked LG E900 with the RIFF Box requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E900:

  •  Solder JTAG cable to LG E900 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E900 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume down’ and ‘Camera’ keys and press ‘Power ON’ button.

.
lg_e900_optimus_7_2

RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

Posted on by

15.01.2013 RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

Repairing bricked HTC DesireV (PL1110000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.14.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PL1110000’.

To resurrect HTC DesireV (PL1110000):

  •  Solder JTAG cable to HTC DesireV (PL1110000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC DesireV (PL1110000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_v_t328w_2

RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

29.12.2012  RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC OneS (PJ4010000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.06.0000 or 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4010000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS PJ4010000 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_s

RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

Posted on by

29.12.2012  RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

Repairing bricked HTC ChaCha (HTC Status) (PH0613000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH0613000’.

To resurrect HTC ChaCha:

  •  Solder JTAG cable to HTC ChaCha (PH0613000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC ChaCha (PH0613000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_status

RIFF JTAG – Haier C2010 Ubrick – Dead Boot repair supported

Posted on by

29.12.2012   RIFF JTAG – Haier C2010 Ubrick – Dead Boot repair supported

Resurrecting Haier C2010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0020/0x8832

To resurrect Haier C2010:

  •  Solder JTAG cable to Haier C2010 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Haier C2010 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

.
haier-c2010-mobile-phone-medium-1