Tag Archives: Operation Completion

RIFF JTAG – Samsung Nexus S (i9023) Unbrick Boot repair supported

Posted on by

04.05.2011  Samsung Nexus S (i9023) Unbrick Boot repair supported

Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung I9023:

  • Solder JTAG cable to Samsung I9023 JTAG pads;
  • Connect microUSB cable to phone and PC;
  • Insert battery;
  • Make sure Samsung I9023 is selected in the list of models;
  • Make sure a fixed TCK frequency is selected;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported

Posted on by

04.05.2011   HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported

Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000’.

To resurrect HTC Incredible C:

  • Solder JTAG cable to HTC Incredible C JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Incredible C is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
  • Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported

Posted on by

03.05.2011   Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported

Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.

To resurrect Samsung B2710 do this:

  • Solder JTAG cable to the Samsung B2710 JTAG pads;
  • Connect USB cable to phone and PC;
  • Make sure Samsung B2710 is selected in the list of models
  • Click Resurrect button;
  • Wait few seconds until software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘9’ keys and press Power-On. Screen lights up with Download mode message.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Samsung S239 (MPower) Repair supported

Posted on by

26.04.2011  CDMA Samsung S239 (MPower) Repair supported

Resurrecting Samsung S239 is simple. Phone is auto powered on with USB Cable connected; battery presence is not required.

To resurrect Samsung S239:

  • Solder JTAG cable to Samsung S239 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Samsung S239 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC 7 Trophy T8686 (HTC Spark) Unbrick, Unlock, IMEI Repair, CID Update, ModelID Repair supported

Posted on by

22.04.2011   HTC 7 Trophy T8686 (HTC Spark) Unbrick, Unlock, IMEI Repair, CID Update, ModelID Repair supported

Resurrecting HTC Trophy is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.75.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4010000’.

To resurrect HTC Trophy:

  • Solder JTAG cable to HTC Trophy JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Trophy is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume Down’ key and press ‘Power ON’ button.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE C370 Repair supported

Posted on by

22.04.2011  CDMA ZTE C370 Repair supported

Resurrecting ZTE C370 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0098/0x0096

To resurrect ZTE C370:

  • Solder JTAG cable to ZTE C370 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure ZTE C370 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C6000 Repair supported

Posted on by

22.04.2011   CDMA Haier C6000 Repair supported

Resurrecting Haier C6000 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0x2210

To resurrect Haier C6000:

  • Solder JTAG cable to Haier C6000 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C6000 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C5100 Repair supported

Posted on by

22.04.2011  CDMA Haier C5100 Repair supported

Resurrecting Haier C5100 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C5100:

  • Solder JTAG cable to Haier C5100 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C5100 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C2040 Repair supported

Posted on by

22.04.2011  CDMA Haier C2040 Repair supported

Resurrecting Haier C2040 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C2040:

  • Solder JTAG cable to Haier C2040 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C2040 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C3010, LG LSP450T Repair supported

Posted on by

22.04.2011  CDMA Haier C3010, LG LSP450T Repair supported

Resurrecting Haier C3010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chips with IDs 0x00EC/0x257E and 0x017E/0x2210. Proper data will be selected automatically depending on memory ID in your device.

To resurrect Haier C3010:

  • Solder JTAG cable to Haier C3010 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C3010 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Resurrecting LG LSP450T is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0020/0x8867

To resurrect LG LSP450T:

  • Solder JTAG cable to LG LSP450T JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure LG LSP450T is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.