Tag Archives: Modem

RIFF JTAG – HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported

Posted on by

14.02.2012     HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported

Resurrecting HTC Thunderbolt CP (Modem Part) part is easy.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes during connection pressing Power On key may be required.
Please note, CP Part’s power is controlled by the AP Part, thus you may experience constant connection loses after definite ammounts of time (1-2-5-x seconds). If this keeps interferring the resurrection process, solder additionall JTAG interface cable to the AP pads, select AP resurrector DLL, go to the JTAG Read/Write page and halt AP core, then switch back to the CP JTAG interface.

To resurrect HTC Thunderbolt CP (Modem Part) Part:

  •  Solder JTAG cable to HTC Thunderbolt CP JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Thunderbolt CP is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Resurrecting HTC Thunderbolt AP (PDA Part) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.04.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG0510000’.
There is option to reflash BOOT and RECOVERY zones.

_

RIFF JTAG – Unlock/IMEI/TA repair – SonyEricsson x8, x10, x10 Mini, x10 mini pro (e15, e10,u20 etc)

Posted on by

11.11.2011    Unlock/IMEI/TA repair –  SonyEricsson x8, x10, x10 Mini, x10 mini pro (e15, e10,u20 etc)

Resurrecting SonyEricsson phones is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.

With current resurrector you can choose Unlock or Resurrection operation to perform. During resurrection, you can select which areas to be repaired. Please note, in some cases phone reports failure during firmware update: in this case you may need to select option to erase Modem SW zone during resurrection.

Example :

During Unlock operation full backup of relevant zones is made, thus you have no risk killing your phone permanently – you have always an option to restore your phone to its original condition with the backup file. Backup files are created in JTAG Manager root directory, in the folder ‘BackupFiles’.

Example :

RIFF JTAG – Samsung i560 Unbrick/Repair dead boot supported

Posted on by

18.10.2010  Samsung i560 Unbrick/Repair dead boot supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.

“Samsung_i560_mdm.dll” contains pinout, instructions and required repair files for i560 and i568 modem part.
“Samsung_i560_PDA.dll” contains pinout, instructions and required repair files for i560 and i568 PDA part.

RIFF JTAG – JTAG Manager v1.13, JTAG Firmware v1.13 released

Posted on by

27.08.2010 JTAG Manager v1.13, JTAG Firmware v1.13 released

Whats new:

JTAG Manger 1.13
———————
– Added feature to display FLASH chip capacity information
– Added feature ‘Auto FullFlash size’ to DCC Read/Write page for simplified Full Images reading/writting
– Fixed DCC Loader Settings dialog
– Added resurrector interface function ‘GetChipSize’ which now enables resurrector DLL to receive target’s memory size
for proper data selection for flashing (like in Huawei Modem E1550 64/128MB versions);

Firmware 1.13
———————
– fixed ARM9 core debug capabilities when core is in Thumb mode
(when ARM9 core was entering debug from Thumb state some CPSR register’s flags were lost, same was when core was leaving debug into Thumb mode);
– FFFFFFEE instruction was added into HAS scripts processing module;

Click “Check for Updates” button to download new JTAG Manager and JTAG firmware.

RIFF Box Support

Posted on by


RIFF Box Viber community
Scan QR code to join, or click above link.

Getting  started with RIFF JTAG
Riff Box short notes for novices Continue reading →