Tag Archives: Mode Screen

RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Posted on by

13.11.2012 RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Resurrecting HTC WildFireS CDMA is easy with RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 (for NAND chips with 4Kb page size). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG7620000’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS CDMA:

  •  Solder JTAG cable to HTC WildFireS CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC WildFireS CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

.

RIFF JTAG – LG E510 Optimus Hub (LG Univa) Supported

Posted on by

23.03.2012  RIFF JTAG – LG E510 Optimus Hub (LG Univa) Supported

Repairing bricked LG E510 with the RIFF Box is not very hard but it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E510:

  •  Solder JTAG cable to LG E510 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E510 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button. In few seconds you should see emergency mode screen saying “DOWNLOAD MODE”.

.

RIFF JTAG – LG P350 Pecan / Optimus Me Unbrick – Boot Repair supported

Posted on by

12.03.2012   RIFF JTAG – LG P350 Pecan / Optimus Me Unbrick – Boot Repair supported

Resurrecting LG P350 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG P350:

  •  Solder JTAG cable to LG P350 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG P350 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods. We used KDZ_FW_UPD update software (with settings Type = 3GQCP, PhoneMode = EMERGENCY) to flash the *.KDZ firmware into phone.

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button. In few seconds you should see emergency mode screen saying “DOWNLOAD MODE”.

.

RIFF JTAG – LG SH860 Supported

Posted on by

24.10.2011  LG SH860 Supported


Resurrecting LG SH860 is easy. To establish connector battery must be connected and Power On key to be pressed.

To resurrect LG SH860:

  •  Solder JTAG cable to LG SH860 JTAG pads;
  •  Insert battery;
  •  Make sure LG SH860 is selected in the list of models;
  •  Click Resurrect button;
  •  Press ‘Power ON’ key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘5’ key and press ‘Power ON’ button. In few seconds you should see emergency mode screen.

RIFF JTAG – LG GM730 Unbrick – Boot repair supported

Posted on by

30.08.2011  LG GM730 Unbrick – Boot repair supported

Resurrecting LG GM730 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).

To resurrect LG GM730:

  •  Solder JTAG cable to LG GM730 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG GM730 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume down’ and ‘Volume up’ keys and press ‘Power ON’ button. In few seconds you should see emergency mode screen.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Wildfire S A510E (HTC Marvel), More CDMA models supported

Posted on by

07.07.2011  HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.

Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS:

  •  Solder JTAG cable to HTC WildFireS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC WildFireS is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.
 

Following CDMA models are supported from today :
  • Samsung B139 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B259 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B309 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B319 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B379 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B619 Repair/Unbrick, Read/Write NOR Flash
  • Huawei C31 Repair, Read/Write NOR flash
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.