Tag Archives: Message Press

RIFF JTAG – Samsung GT-S6810P Galaxy Fame WORLD FIRST Boot repair support ! ! !

Posted on by

07.02.2013  RIFF JTAG – Samsung GT-S6810P Galaxy Fame WORLD FIRST Boot repair support ! ! !

Repairing bricked Samsung S6810P is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S6810P:

  •  Solder JTAG cable to Samsung S6810P JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S6810P is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘OK’ keys and press Power-On. And after you see the warning message press ‘Volume Up’ key to enter Download Mode.

.
samsung_gt-s6810_galaxy_fame

RIFF JTAG – Samsung GT-S6012 Galaxy Music Duos Unbrick – Dead Boot repair supported

Posted on by

29.12.2012  RIFF JTAG – Samsung GT-S6012 Galaxy Music Duos Unbrick – Dead Boot repair supported

Repairing bricked Samsung S6012 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S6012:

  •  Solder JTAG cable to Samsung S6012 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S6012 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘OK’ keys and press Power-On. And after you see the warning message press ‘Volume Up’ key to enter Download Mode.

.
samsung_galaxy_music

RIFF JTAG – CDMA Samsung SPH-D700 Galaxy S Epic 4G Unbrick, Dead Boot repair supported

Posted on by

14.03.2011 CDMA Samsung SPH-D700 Galaxy S Epic 4G Unbrick, Dead Boot repair supported

Samsung SPH-D700 is based on the S5PC110 Processor (ARM core is Cortex-A8). Depending on firmware state resurrection can be a bit confusing: for successful connection you will require charged battery. Please note – no matter whether you have USB cable or not – it must not be connected to phone. This is important.
Resurrector will reflash IBL, PBL, SPL and PARAM areas. Additionally you can select KERNEL and RECOVERY partitions to be reflashed too. Though them are required only for recovery mode and not needed for following USB firmware update by Odin software. So if you don’t need recovery mode don’t select these 2 partitions – otherwise you will just waste time waiting for them to be reflashed.
If after resurrection the download mode still cannot be initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung SPH-D700:

  • Solder JTAG cable to Samsung SPH-D700 JTAG pads;
  • Make sure USB cable or charger is not connected;
  • Make sure Samsung SPH-D700 is selected in the list of models;
  • Make sure a fixed TCK frequency is selected;
  • Insert battery;
  • Click Resurrect button;
  • Press Power On key; when you will see “Establish communication with the phone…” message – press Power On ey again (and hold it pressed for 1-2 seconds);
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download or recovery mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘1’ key on the keypad and press Power-On to enter download mode;
  • Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter recovery mode.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.