Tag Archives: Memory

RIFF JTAG – HTC EVO Design 4G PH4430(HTC Kingdom) Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

29.03.2013  HTC EVO Design 4G PH4430(HTC Kingdom) Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC EvoDesign4G is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zones and will re-write PDA’s SPL to 1.30.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH4430000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC EvoDesign4G via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure USB cable is attached to the board and is connected to PC;
  •  Make sure HTC EvoDesign4G via USB is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_evo_design_4g

RIFF JTAG – HTC EVO Design 4G / Acquire (HTC Kingdom) Unbrick, IMEI, SuperCID, Unlock repair supported

Posted on by

09.03.2013 RIFF JTAG – HTC EVO Design 4G / Acquire (HTC Kingdom) Unbrick, IMEI, SuperCID, Unlock repair supported

Repairing bricked HTC EvoDesign4G is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zones and will re-write PDA’s SPL to 1.30.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH4410000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC EvoDesign4G via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure USB cable is attached to the board and is connected to PC;
  •  Make sure HTC EvoDesign4G via USB is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_evo_design_4g

RIFF JTAG – Samsung Exynos 4412 QUADCORE Supported

Posted on by

09.03.2013 RIFF JTAG – Samsung Exynos 4412 QUADCORE Supported

Resurrector Exynos4412 eMMC0 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager, or with eMMC Plugin.
DCC Loader expects eMMC memory to be connected to the SDCC controller #0.

Please note that only nonsecured MCU-s will work (DBGEN=1). In case that MCU is secured, HALT operatoion will fail with error 0x44.

Exynos-4412

RIFF JTAG – HTC Radar (HTC Omega) Unbrick, Unlock, SuperCID and IMEI update via USB cable supported

Posted on by

12.06.2012   RIFF JTAG – HTC Radar (HTC Omega) Unbrick, Unlock, SuperCID and IMEI update via USB cable supported

Repairing bricked HTC Radar (PI06100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI0610000’.

To resurrect HTC Radar via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure HTC Radar (PI06100) is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Depower the phone;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

.

RIFF JTAG – HTC One V T320e (HTC Primo) Unbrick, Unlock, SuperCID, IMEI Repair supported

Posted on by

31.05.2012  RIFF JTAG – HTC One V T320e (HTC Primo) Unbrick, Unlock, SuperCID, IMEI Repair supported

Repairing bricked HTC OneV (PK76100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.16.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PK7610000’.
There is option to reflash android BOOT and RECOVERY zones.

To resurrect HTC OneV via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure HTC OneVC (PK76100) is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Desire new security supported

Posted on by

16.12.2010  HTC Desire New security supported

New DLL contains updated DCC loader in order to support different memory map layout, and support for 4kb paging.

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“HTC_Desire.dll” contains pinout, repair instructions and required files for single click HTC Desire Unlock, Unbrick, IMEI repair.

RIFF Box JTAG Manager Version 1.17- JTAG Pins Detection added, WORLD FIRST

Posted on by

14.10.2010 RIFF JTAG Manager v1.17 released

Whats new :

  • Addedd chip size information handling for NOR memories
  • Improved erase operation in case DCC Loader operates with a NOR memory.
  • Implemented ResBreak option (SYSTEM.OPTION RESBREAK ON|OFF) in the Trace32 CMM execution engine
  • Added PROBE feature – Detection of JTAG Pins ! ! !

Probing function work via Pin 6 on RJ45 Port :

Advanced users should read the probing manual from here.

Probe dialog example :

_____________________________

RIFF Box firmware v1.15 :

– Probe (JTAG Pins detection) feature added

RIFF JTAG – HTC Desire with SLCD , Direct Unlock update

Posted on by

20.09.2010 – HTC Desire new revision boards supported!

Whats new:

  • Added optional selection for SPL versions
  • Added direct Unlock function without SPL reflashing

As already noted before, the HTC Desire is being shipped now with SLCD display type, instead of previous AMOLED.
Now You can chose SPL version to be used, 0.80.0000, or 0.92.0007. Latest SPL supports both display types, but at the moment this SPL isn’t rooted as we know.

Here is how it works now:

If You want just to repair the SPL, Untick the IMEI and HTC Partition check boxes.
If phone IMEI or eeprom is damaged, You need to tick the HTC Partition and IMEI check boxes, and of course fill out the desired IMEI.

If You just want to unlock phone, without any other changes, select “Unlock Settings” TAB and press “Unlock” button:

This function will unlock the phone without touching any other memory part.