Tag Archives: Jtag Interface

RIFF JTAG – HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported

Posted on by

14.02.2012     HTC ThunderBolt 4G ADR6400 (HTC Mecha) Unbrick – Boot repair supported

Resurrecting HTC Thunderbolt CP (Modem Part) part is easy.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes during connection pressing Power On key may be required.
Please note, CP Part’s power is controlled by the AP Part, thus you may experience constant connection loses after definite ammounts of time (1-2-5-x seconds). If this keeps interferring the resurrection process, solder additionall JTAG interface cable to the AP pads, select AP resurrector DLL, go to the JTAG Read/Write page and halt AP core, then switch back to the CP JTAG interface.

To resurrect HTC Thunderbolt CP (Modem Part) Part:

  •  Solder JTAG cable to HTC Thunderbolt CP JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Thunderbolt CP is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Resurrecting HTC Thunderbolt AP (PDA Part) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.04.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG0510000’.
There is option to reflash BOOT and RECOVERY zones.

_

RIFF JTAG – HTC Droid Incredible 2 ADR6350 Boot repair, Unlock, CID, ModelID, IMEI Update

Posted on by

HTC Droid Incredible 2 ADR6350 Boot repair, Unlock, CID, ModelID, IMEI Update

Resurrecting HTC Incredible 2 (Droid Incredible 2 ADR6350VW) is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Incredible 2 boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8655 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 6.13.1002. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG3210***’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Incredible 2:

  •  Solder JTAG cable to HTC Incredible 2 JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Incredible 2 is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

_

RIFF JTAG – HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported

Posted on by

HTC Panache/Glacier/My Touch 4G Unbrick, IMEI, CID, ModelID, Unlock supported

Resurrecting HTC Glacier is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Glacier boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write SPL version 0.86.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD1510000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Glacier:

  •  Solder JTAG cable to HTC Glacier JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Glacier is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

    _

RIFF JTAG – HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported

Posted on by

HTC Inspire 4G A9192 (HTC Stallion) Unbrick, Boot, IMEI, CID, ModelID, Unlock supported

Resurrecting HTC Inspire is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Inspire boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 0.85.0024. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD9812000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Inspire:

  •  Solder JTAG cable to HTC Inspire JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Inspire is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

_

RIFF JTAG – Samsung GT-i9103 Galaxy Z / Galaxy R Boot repair / Unbrick

Posted on by

31.12.2011   A new Year gift ! Samsung GT-i9103 Galaxy Z / Galaxy R (TEGRA2)  Boot repair / Unbrick

Resurrecting Samsung I9103 is easy.
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes pressing Power On key during connection may be required. External power supply can be used too.
During some definite startup time (1…3 seconds) TEGRA2 chipsets are not detected via JTAG interface (this could be due to FUSE-d security): that is, on contrary to other devices, which being fused are detected via JTAG but non-haltable, TEGRA2 chipsets give ‘Nothing Detected’ response (though TCK-RTCK pair keeps functioning ok).
Please note: If during resurrection of dead unit the JTAG connection cannot be established (nothing is detected) then re-try with the NRST wire disconnected.

To resurrect Samsung I9103:

  •  Solder JTAG cable to Samsung I9103 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung I9103 is selected in the list of models;
  •  Click Resurrect button;
  •  If nothing is detected then try with NRST wire disconnected;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
_

RIFF JTAG – HTC Incredible S Unbrick, Unlock, CID, IMEI repair supported

Posted on by

30.12.2011    HTC Incredible S Unbrick, Unlock, CID, IMEI repair supported

 

Resurrecting HTC Incredible S is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Incredible S boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.13.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG3213000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Incredible S:

  •  Solder JTAG cable to HTC Incredible S JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Incredible S is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

_

RIFF JTAG – Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported

Posted on by

29.12.2011      Samsung Galaxy Note (GT-i9220) Unbrick – Boot Repair Supported

Samsung I9220 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I9220 AP:

  •  Solder JTAG cable to Samsung I9220 AP JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9220 AP is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

_

RIFF JTAG – Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Posted on by

28.12.2011    Samsung Galaxy Note (GT-N7000) Unbrick – Dead Boot Repair supported

Samsung N7000 AP (PDA Part) is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung N7000 AP:

  •  Solder JTAG cable to Samsung N7000 AP JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung N7000 AP is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

_

RIFF JTAG – HTC Desire Z (HTC Vision) Unbrick, Unlock, IMEI&CID repair supported

Posted on by

12.10.2011    HTC Desire Z (HTC Vision) Unbrick, Unlock, IMEI&CID repair supported

Resurrecting HTC Desire Z is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Desire Z boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM7230 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.

Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write one of selected PDA’s SPL versions (0.76.2000 or 0.85.0005). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC1010000’.
There is option to reflash BOOT and RECOVERY zones.

Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Desire Z:

  •  Solder JTAG cable to HTC Desire Z JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Desire Z is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

RIFF JTAG -Samsung Galaxy II, OMAP4430 version supported (Samsung i9100G, Samsung i9108)

Posted on by

07.10.2011    Samsung Galaxy II, OMAP4430 version supported (Samsung i9100G, Samsung i9108)

Samsung I9108 is based on the OMAP4430 Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface. There is a big variety of versions of Galaxy II devices: GT-I9100, GT-I9100G, GT-I9100L, GT-I9100M, GT-I9100T, GT-I9101, GT-I9103, GT-I9108, GT-I9188, and maybe more. Some of them are based on different hardware platform – the Samsung S5PV310 (Cortex-A9 Dual-Core). Thus make sure first which exact hardware version you have on hands.

Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
Current DLL is still a beta one. It will work only with phones which have killed X-Loader.

To resurrect Samsung I9108:

  •  Solder JTAG cable to Samsung I9108 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9108 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.