Tag Archives: Jtag Cable

RIFF JTAG – CDMA Huawei C2830 Boot repair supported

Posted on by

06.04.2011    CDMA Huawei C2830 Boot repair supported

Resurrecting Huawei C2830 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Since the JTAG test points are placed under keyboard sticker we recommend using USB data cable to supply power to the device.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x5FFFFF).
Please note: if you do not have JIG (that is you solder wires instead) then black graphite covering has to be carefully scratched off in order to access copper surface of the pads.

To resurrect Huawei C2830:

  • Solder JTAG cable to Huawei C2830 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Huawei C2830 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Micromax C111 Boot repair supported

Posted on by

06.04.2011  CDMA Micromax C111 Boot repair supported

Resurrecting Micromax C111 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
There are 2 different hardware revisions of this phone – one is based on Qualcomm QSC1100 MCU and other – is Qualcomm QSC6010 MCU. Current resurrector shall be selected if you have QSC1100 revision.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x6FFFFF).

To resurrect Micromax C111:

  • Solder JTAG cable to Micromax C111 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Micromax C111 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported

Posted on by

31.03.2011    HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported

Resurrecting HTC Chief is easy:
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.44.0000 SPL version.
Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘CEDA10000’.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.

To resurrect HTC Chief:

  • Solder JTAG cable to HTC Chief JTAG pads;
  • Make sure HTC Chief is selected in the list of models;
  • Insert battery and connect USB Cable;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – RoverPC EVO V7 Unbrick – Dead boot repair supported

Posted on by

21.03.2011  RoverPC EVO V7 Unbrick – Dead boot repair supported

RoverPC Evo V7 resurrection is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect RoverPC Evo V7:

  • Solder JTAG cable to RoverPC Evo V7 JTAG pads;
  • Connect USB cable to phone and PC;
  • Make sure RoverPC Evo V7 is selected in the list of models;
  • Make sure a fixed TCK frequency is selected;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original firmware downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Huawei E153U Broadband modem unbrick – dead boot repair supported

Posted on by

17.03.2011  Huawei E153U Broadband modem unbrick – dead boot repair supported

Resurrecting Huawei E153U is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
There are secured (QCSBL is signed) and non-secured (QCSBL is not signed) modem revisions exist. Resurrector will automatically detect board revision and will select proper data to be flashed.
No matter what h/w revision is you can select which partitions are to be flashed during resurrection process.

To resurrect Huawei E153U:

  • Solder JTAG cable to Huawei E153U JTAG pads;
  • Insert Huawei E153U modem into any USB port for power;
  • Make sure Huawei E153U is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung SGH-i607 BlackJack PDA Unbrick, Dead Boot repair supported

Posted on by

12.03.2011  Samsung SGH-i607 BlackJack PDA Unbrick, Dead Boot repair supported

Resurrecting Samsung i607 PDA part is easy. Phone requires battery presence in order to establish JTAG connection. If you additionally connect charger the phone will be auto powered on and there will be no need to press Power on key.
In case you experience connection problems, de-power phone completely, disconnect charger (if it was used), then insert battery, click Resurrection button in the JTAG Manger and immediately (within 0…1 seconds) press Power On key.

To unbrick Samsung i607 PDA part:

  • Solder JTAG cable to Samsung i607 PDA JTAG pads;
  • Make sure Samsung i607 PDA is selected in the list of models;
  • If only battery is connected – press Power On key shortly;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Huawei C5005 Unbrick – Repair supported

Posted on by

11.03.2011  CDMA Huawei C5005 Unbrick – Repair supported

Resurrecting Huawei C5005 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0xBFFFFF).

To resurrect Huawei C5005:

  • Solder JTAG cable to Huawei C5005 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Huawei C5005 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Tattoo A3232 (HTC Click 1100) Unlock, Unbrick, IMEI repair, CID Update

Posted on by

10.03.2011 HTC Tattoo A3232 (HTC Click 1100) Unlock, Unbrick, IMEI repair, CID Update supported

Resurrecting HTC Click is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside.
There are two different hardware versions exist – one based on the MSM7225 chipset (CLIC10000) and other – on the ESM7225 chipset (CLIC11000). In resurrector settings you can select a desired version.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.52.0001 SPL version.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.

To resurrect HTC Click:

  • Solder JTAG cable to HTC Click JTAG pads;
  • Make sure HTC Click is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To Unlock HTC Click :

  • Solder JTAG cable to HTC Click JTAG pads;
  • Make sure HTC Click is selected in the list of models;
  • Click Resurrect button;
  • Select “Unlock Settings” TAB
  • Select Unlock method
  • Click “Unlock”

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – ASUS P526 Unbrick, Dead Boot repair supported

Posted on by

10.03.2011   ASUS P526 Unbrick, Dead Boot repair supported

Resurrection of ASUS P526 is slightly complicated. JTAG pads are very small and sensitive thus extreme care must be taken when soldering wires to the board. Battery must be connected in order to establish JTAG connection.
Current resurrector re-flashes only the IPL area, and will not re-write MDOC XLOADER area (though write of this area is supported too).
Please note: DiskOnChip G4 memory has security features, due to which there is a risk of permanently blocking the access to the flash memory while re-flashing the XLOADER areas. Current resurrector will not touch the XLOADER zone, but it is possible you’re already holding such killed device in hands. If it is so you will see this error:
****************************************************************
Detected a Not Initialized FLASH1 Chip ID: 0x0400/0xFBFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader
****************************************************************

This can happen due to unknown protection keys used or due to permanently blocked MDOC chip. If latter is true we advise you to solder a new flash memory chip or throw this phone away to the trash bin.

To resurrect ASUS P526:

  • Solder JTAG cable to ASUS P526 JTAG pads;
  • Insert battery and connect USB cable to phone and PC;
  • Make sure ASUS P526 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
If phone not enters download mode after resurrection then it means XLOADER was damaged too but memory chip is still usable. In this case repeat resurrection using RAM Downloader Mode and when USB connection is established reflash the phone with official firmware.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Move ‘Lock’ slider down, hold ‘OK’ key (on the left) and press ‘Power ON’ button. In few seconds you should see TriColor picture.

Additional info:

  • Phone has DiskOnChip G4 memory type, which has security features. It has two password protected partitions (Password1 = 12345678, Password2 = 00000000);
  • XLOADER re-flash is not performed in this resurrector on purpose. While re-flashing the XLOADER area there is a risk of permanently blocking the memory chip.
  • Any write access (Erase or Write) on MDOC NAND memory range 0x00000000 to 0x0017FFFF is rejected by the DCC Loader

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE F285 Repair supported

Posted on by

10.03.2011 CDMA ZTE F285 Repair supported

Resurrecting ZTE F285 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x60FFFF).
To resurrect ZTE F285:

  • Solder JTAG cable to ZTE F285 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure ZTE F285 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.