Tag Archives: Jtag Cable

RIFF JTAG -Sierra Wireless 597 AirCard – Unbrick – Boot repair supported

Posted on by

30.08.2011  Sierra Wireless 597 AirCard – Unbrick – Boot repair supported

Resurrecting CDMA USB Modem Sierra 597 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
You can select which areas to be repaired during requrrection process.

To resurrect CDMA USB Modem Sierra 597:

  •  Solder JTAG cable to Sierra 597 JTAG pads;
  •  Insert Sierra 597 into any USB port for power;
  •  Make sure USB Modem 597 is selected in the list of models;
  •  Click Resurrect button;
  •  Select areas to be repaired in the settings window;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Sierra Wireless U595 USB Modem, Unbrick – Boot repair supported

Posted on by

30.08.2011  Sierra Wireless U595 USB Modem, Unbrick – Boot repair supported

Resurrecting CDMA USB Modem Sierra U595 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
Please note, there is back cover detecting micro-switch present on the board: without back cover modem will not receive power. Thus, either asemble modem with soldered wires and attach back cover or hold micro-switch manually during all resurrection process.
You can select which areas to be repaired during requrrection process.

To resurrect CDMA USB Modem Sierra U595:

  •  Solder JTAG cable to Sierra U595 JTAG pads;
  •  Insert Sierra U595 into any USB port for power;
  •  Make sure USB Modem U595 is selected in the list of models;
  •  Click Resurrect button;
  •  Select areas to be repaired in the settings window;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung A837 Unbrick – Boot repair supported

Posted on by

30.08.2011     Samsung A837 Unbrick – Boot repair supported

The Samsung A837 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung A837:

  •  Solder JTAG cable to Samsung A837 JTAG pads;
  •  connect USB cable;
  •  Make sure Samsung A837 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘9’ key and press ‘Power ON’ button.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung Galaxy 551 (i5510) Unbrick – Boot repair supported

Posted on by

30.08.2011   Samsung Galaxy 551 (i5510) Unbrick – Boot repair supported

Samsung I5510 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung I5510 do this:

  •  Solder JTAG cable to Samsung I5510 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung I5510 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Emergency Mode;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Wizard 200 Unbrick – Boot repair supported

Posted on by

25.08.2011  HTC Wizard 200 Unbrick – Boot repair supported

Resurrection of HTC Wizard 200 is simple. Battery must be connected in order to establish JTAG connection.
Current resurrector works with devices based on G4 MDOC chip.
Resurrector can repair IPL and SPL areas (which areas to repair you can select in popup window).
Please note: DiskOnChip G4 memory has security features, due to which there is a risk of permanently blocking the access to the flash memory while re-flashing the IPL area. Thus be very carefull not to interrupt IPL repair process (in case you have selected IPL area to be repaired).
In case your device has permanently blocked MDOC memory you will see this error:

****************************************************************
Detected a Not Initialized FLASH1 Chip ID: 0x0400/0xFBFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader
****************************************************************
This can happen due to unknown protection keys used or due to permanently blocked MDOC chip. If latter is true we advise you to solder a new flash memory chip or throw this phone away to the trash bin.
To resurrect HTC Wizard:

  •  Solder JTAG cable to HTC Wizard JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure HTC Wizard is selected in the list of models;
  •  Press Power On key
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Camera’ key and press ‘Power ON’ button.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung Galaxy GIO (S5660) Unbrick – Boot repair supported

Posted on by

23.08.2011    Samsung Galaxy GIO (S5660) Unbrick – Boot repair supported

Samsung S5660 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5660 do this:

  •  Solder JTAG cable to Samsung S5660 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung S5660 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung Galaxy Tab M180s Unbrick – Boot Repair supported

Posted on by

03.08.2011     Samsung Galaxy Tab M180s Unbrick – Boot Repair supported

Samsung M180S is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung M180S:

  •  Solder JTAG cable to Samsung M180S JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Attach battery connector;
  •  Make sure Samsung M180S is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported

Posted on by

02.08.2011   Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported

Resurrecting SE X8 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X8:

  •  Solder JTAG cable to SE X8 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE X8 is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

 

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Sony Ericsson Xperia X10a mini / E10a (SE Robyn) Unbrick – Boot repair supported

Posted on by

02.08.2011    Sony Ericsson Xperia X10a mini / E10a (SE Robyn) Unbrick – Boot repair supported

Resurrecting SE X10 Mini is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X10 Mini:

  •  Solder JTAG cable to SE X10 Mini JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE X10 Mini is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – SonyEricsson Xperia X10 Unbrick – Boot repair supported

Posted on by

30.07.2011     SonyEricsson Xperia X10 Unbrick – Boot repair supported

Resurrecting SE X10 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Be careful, JTAG pads are covered under blue mask covering, so you will need to scratch it off in order to be able to solder wires.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.

To resurrect SE X10:

  •  Solder JTAG cable to SE X10 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE X10 is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.