RIFF JTAG – CDMA Huawei C3500 Supported

23.12.2011    CDMA Huawei C3500 Supported 

Resurrecting Huawei C3500 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Huawei C3500:

  •  Solder JTAG cable to Huawei C3500 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Huawei C3500 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Huawei C2856 Supported

22.11.2011  CDMA Huawei C2856 Supported

Resurrecting Huawei C2856 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0020/0x88C0

To resurrect Huawei C2856:

  •  Solder JTAG cable to Huawei C2856 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Huawei C2856 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Haier C301R supported

20.12.2011   CDMA Haier C301R supported

Resurrecting Haier C301R is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C301R:

  •  Solder JTAG cable to Haier C301R JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Haier C301R is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

RIFF JTAG – Lenovo LePhone 3G W100 Unbrick – Boot repair supported

19.12.2011  Lenovo LePhone 3G W100 Unbrick – Boot repair supported

Resurrecting Lenovo LePhone 3GW100 is easy. To establish JTAG connection make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
To resurrect Lenovo LePhone 3GW100:

  •  Solder JTAG cable to Lenovo LePhone 3GW100 JTAG pads;
  •  Insert battery;
  •  Make sure Lenovo LePhone 3GW100 is selected in the list of models;
  •  Press and hold Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

RIFF JTAG – CDMA Motorola w210 supported

16.12.2011 CDMA Motorola w210 supported

Resurrecting Motorola W210 is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0089/0x8855

To resurrect Motorola W210:

  •  Solder JTAG cable to Motorola W210 JTAG pads;
  •  Connect charger for auto power on or use battery;
  •  Make sure Motorola W210 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;
_

RIFF JTAG – Samsung Star Duos (C6712) Unbrick – Boot repair supported

29.11.2011  Samsung Star Duos (C6712) Unbrick – Boot repair supported

Samsung C6712 resurrection is simple. Battery is not required. To power the board it’s most convenient to use an USB Data Cable.
In order to contact to JTAG pads you may need to carefully scratch off paint covering (mask layer) above them. Sometimes there is reset problem with these phones, thus you may need to disconnect and then connect USB cable again.

To resurrect Samsung C6712 do this:

  •  Solder JTAG cable to Samsung C6712 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung C6712 is selected in the list of models
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘SIM Swap’ keys and press Power-On.
__

RIFF JTAG – Unbrick Samsung Galaxy TAB Wi-Fi (P1010), more CDMA Models supported

22.11.2011  Unbrick Samsung Galaxy TAB Wi-Fi (P1010), more CDMA Models supported

Samsung P1010 is based on the OMAP3630 (ARM core is Cortex-A8).

Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
Please note, in most cases you will be required to insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot before starting resurrection. In case you don’t have such card yet, you can create it on the “Samsung P1010 RIFF™ MagicCard” page of the resurrector settings dialog.
This is IRAM version of the Samsung P1010 resurrector. We recommend you using it only in case you had problems connecting to phone with normal Samsung P1010 resurrector DLL.

To resurrect Samsung P1010:

  •  Solder JTAG cable to Samsung P1010 JTAG pads;
  •  Insert Samsung P1010 RIFF™ MagicCard into phone’s SD slot;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung P1010 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
There are two DLL-s (Normal and iRAM version) – You can use iRam version in case normal one doesnt work properly. iRam version is much slower, but more robust.
CDMA Models added today :
  • ZTE  AC2766
  • ZTE  AC2746
  • AnyData  ADU555C
Please click “Check for Updates” button in order to download and install new updates.

RIFF JTAG – LG P999 G2X (LG Star) Modem unbrick/repair supported

19.11.2011  LG P999 G2X (LG Star) Modem unbrick/repair supported

Resurrecting LG P999 Modem part is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes during connection pressing Power On key may be required.

To resurrect LG P999 Modem Part:

  •  Solder JTAG cable to LG P999 Modem JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG P999 Modem is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

 

RIFF JTAG – Samsung i9003 Galaxy SL Unbrick, Boot repair supported

28.10.2011  Samsung i9003 Galaxy SL Unbrick, Boot repair supported

Samsung I9003 is based on the OMAP3630 (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
Please note, in most cases you will be required to insert Samsung I9003 RIFF™ MagicCard into phone’s SD slot before starting resurrection. In case you don’t have such card yet, you can create it on the “Samsung I9003 RIFF™ MagicCard” page of the resurrector settings dialog.
Due to OMAP3630’s some peculiar TrustZone security features current resurrector may fail to boot: if this happens, use Samsung I9003 IRAM resurrector – which works much slower but boots without problems.

To resurrect Samsung I9003:

  •  Solder JTAG cable to Samsung I9003 JTAG pads;
  •  Insert Samsung I9003 RIFF™ MagicCard into phone’s SD slot;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung I9003 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

RIFF JTAG – CDMA ZTE R518 supported

28.10.2011   CDMA ZTE R518 supported

Resurrecting ZTE R518 is easy. Battery is not required. To power the board it’s most convenient to use an USB Data Cable

To resurrect ZTE R518:

  •  Solder JTAG cable to ZTE R518 JTAG pads;
  •  Make sure ZTE R518 is selected in the list of models;
  •  Connect USB Data Cable;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;