Tag Archives: Initiation

RIFF JTAG – T-Mobile myTouch2 3G Slide (HTC Espresso) Unbrick /Unlock/ Repair Boot, IMEI, CID supported

Posted on by

16.10.2012   RIFF JTAG – T-Mobile myTouch2 3G Slide (HTC Espresso) Unbrick /Unlock/ Repair Boot, IMEI, CID supported

Repairing bricked HTC Espresso is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.02.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB6510000’.

To resurrect HTC Espresso:

  •  Solder JTAG cable to HTC Espresso JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Espresso is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC ChaCha A810e Unbrick, IMEI, SuperCID and Simlock repair supported

Posted on by

05.10.2012    RIFF JTAG – HTC ChaCha A810e  Unbrick, IMEI, SuperCID and Simlock repair supported

Repairing bricked HTC ChaCha is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.04.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH06*****’.

To resurrect HTC ChaCha:

  •  Solder JTAG cable to HTC ChaCha JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC ChaCha is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Explorer (HTC Pico) Unbrick, Unlock, SuperCID IMEI repair

Posted on by

13.07.2012  RIFF JTAG – HTC Explorer (HTC Pico) Unbrick, Unlock, SuperCID IMEI repair

 

Repairing bricked HTC Explorer is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ0310000’.

To resurrect HTC Explorer:

  •  Solder JTAG cable to HTC Explorer JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Explorer is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.

RIFF JTAG – HTC 7 Surround T8788 (HTC Mondrian) Unbrick, Unlock, SuperCID and IMEI repair supported

Posted on by

23.05.2012  RIFF JTAG – HTC 7 Surround T8788 (HTC Mondrian) Unbrick, Unlock, SuperCID and IMEI repair supported

Repairing bricked HTC Surround (PD26100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.74.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD26*****’.

To resurrect HTC Surround (PD26100):

  •  Solder JTAG cable to HTC Surround JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Surround (PD26100) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Lenovo LePhone 3G W100 Unbrick – Boot repair supported

Posted on by

19.12.2011  Lenovo LePhone 3G W100 Unbrick – Boot repair supported

Resurrecting Lenovo LePhone 3GW100 is easy. To establish JTAG connection make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
To resurrect Lenovo LePhone 3GW100:

  •  Solder JTAG cable to Lenovo LePhone 3GW100 JTAG pads;
  •  Insert battery;
  •  Make sure Lenovo LePhone 3GW100 is selected in the list of models;
  •  Press and hold Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

RIFF JTAG – HTC Desire CDMA Supported

Posted on by

24.10.2011  HTC Desire CDMA Supported

Resurrecting HTC Desire CDMA is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.60.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PP9940000’.
Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC Desire CDMA:

  •  Solder JTAG cable to HTC Desire CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Desire CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Back’ key and press ‘Power ON’ button.

RIFF JTAG – HTC Supersonic (EVO 4G) Unbrick, Unlock, IMEI, CID, ModelID repair supported

Posted on by

24.10.2011   HTC Supersonic (EVO 4G) Unbrick, Unlock, IMEI, CID, ModelID repair supported

Resurrecting HTC Supersonic (EVO 4G) is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.16.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC3610000’.
Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code. If selected, then ClockworkMod Recovery v5.0.2.2 will be flashed. Using this recovery you will be able to install zip files from the SD Card, for example you will be able to acquire ROOT rights by installing su-2.3.6.3-efgh-signed.zip file.

To resurrect HTC Supersonic:

  •  Solder JTAG cable to HTC Supersonic JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Supersonic is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

RIFF JTAG – Qtek 9000 (HTC Universal) Unbrick – Boot repair supported

Posted on by

15.07.2011  Qtek 9000 (HTC Universal) Unbrick – Boot repair supported

Current resurrector works with Qtek 9000 with MDOC G3 memory version. In order to establish JTAG connection charged battery is required. In some cases you will need to press power on key during initiating connection.
Please note, in case the Download Mode Initiation resurrection way is selected in the resurrector popup settings window, battery must be charged enough in order for phone to enter download mode.

Current resurrector offers 2 ways to resurrect the phone:

  •  WAY1: Writing SPL code directly into the MDOC memory (there are 2 hardware versions of the Qtek 9000 exist: boards with G4-type MDOC memory and boards with G3-type MDOC memory; current resurrector contains DCC Loader for G3 MDOC memory; thus for G4 version you need to use other resurrector)

 

  •  WAY2: Initiating DOWNLOAD MODE without touching MDOC contents;

MDOC G3 memory has security features, due to which there is a risk of permanently blocking the access to the flash memory while re-flashing the IPL loader. Current resurrector will not touch the IPL zone, but it is possible you’re already holding such killed device in hands. If it is so you will see this error:

****************************************************************
Detected a Not Initialized FLASH1 Chip ID: 0x0200/0xFDFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader
****************************************************************
In this case resurrection of your device is not possible. We advise you to solder a new flash memory chip and then use resurrector with IPL re-flash enabled.
To resurrect Qtek 9000 G3:

  •  Solder JTAG cable to Qtek 9000 G3 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Qtek 9000 G3 is selected in the list of models;
  •  Click Resurrect button;
  •  In popup window select desired way of resurrection;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Light’ key (the one near to the volume slider) and ‘Power On’ key and press with stylus the reset hole-button.

Additional info:

  •  The DiskOnChip G3 memory type has security features. Access to both protected partitions (as IPL loader area) is done using password 00000000.
  •  IPL re-flash is intentionally switched off in this resurrector. While re-flashing the IPL area there is a risk of permanently blocking the memory chip.
  •  Memory is two DiskOnChip (MDOC) G3 cascaded chips, IDs are 0x0200; capacity is 64Mb+64Mb); though current DCC Loader was tested to read/write correctly only the SPL zones.

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – HTC Wildfire S A510E (HTC Marvel), More CDMA models supported

Posted on by

07.07.2011  HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.

Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS:

  •  Solder JTAG cable to HTC WildFireS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC WildFireS is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.
 

Following CDMA models are supported from today :
  • Samsung B139 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B259 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B309 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B319 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B379 Repair/Unbrick, Read/Write NOR Flash
  • Samsung B619 Repair/Unbrick, Read/Write NOR Flash
  • Huawei C31 Repair, Read/Write NOR flash
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported

Posted on by

Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported

The HTC Magic (SAPP400) is based on ESM7206A chipset. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.53.02000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘SAPP*****’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC Magic (SAPP400):

  • Solder JTAG cable to HTC Magic (SAPP400) JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure HTC Magic (SAPP400) is selected in the list of models;
  • If you use battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Back (←)’ key and press ‘Power ON’ button. In few seconds you should see download mode saying Fastboot USB.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.