Tag Archives: Initiation

RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

Posted on by

09.02.2013   RIFF JTAG – HTC One XL (HTC Evita) Unbrick – Dead boot, Unlock, SuperCID, IMEI repair supported

Repairing bricked HTC OneXL (PJ8312000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8312000’.

To resurrect HTC OneXL (PJ8312000):

  •  Solder JTAG cable to HTC OneXL (PJ8312000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneXL (PJ8312000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_xl

RIFF JTAG – HTC Droid DNA ADR6435 / Droid Incredible X (HTC DLX) Unbrick, Unlock, IMEI and SuperCID repair supported

Posted on by

RIFF JTAG – HTC Droid DNA ADR6435 / Droid Incredible X (HTC DLX) Unbrick, Unlock, IMEI and SuperCID repair supported

Repairing bricked HTC Droid DNA (PL8320000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.33.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PL8320000’.

To resurrect HTC Droid DNA (PL8320000):

  •  Solder JTAG cable to HTC Droid DNA (PL8320000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Droid DNA (PL8320000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_droid_dna

RIFF JTAG – HTC One X AT&T Unbrick, IMEI, SuperCID repair supported

Posted on by

30.01.2013 RIFF JTAG – HTC One X AT&T(PJ8310000) Unbrick, IMEI, SuperCID repair supported

Repairing bricked HTC OneX (PJ8310000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8310000’.

To resurrect HTC OneX (PJ8310000):

  •  Solder JTAG cable to HTC OneX (PJ8310000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneX (PJ8310000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_x

RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

Posted on by

15.01.2013 RIFF JTAG – HTC Desire V T328w (HTC Wind) Unbrick, IMEI, SuperCID, Boot repair supported

Repairing bricked HTC DesireV (PL1110000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.14.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PL1110000’.

To resurrect HTC DesireV (PL1110000):

  •  Solder JTAG cable to HTC DesireV (PL1110000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC DesireV (PL1110000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_desire_v_t328w_2

RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

29.12.2012  RIFF JTAG – HTC One S PJ401000 Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC OneS (PJ4010000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.06.0000 or 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4010000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS PJ4010000 is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_one_s

RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

Posted on by

29.12.2012  RIFF JTAG – AT&T HTC Status (HTC ChaCha PH0613000) Ubrick, Boot, IMEI, SuperCID repair supported

Repairing bricked HTC ChaCha (HTC Status) (PH0613000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.13.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH0613000’.

To resurrect HTC ChaCha:

  •  Solder JTAG cable to HTC ChaCha (PH0613000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC ChaCha (PH0613000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_status

RIFF JTAG – HTC HD Mini T5555 (HTC Photon) Unbrick, Unlock, IMEI, CID repair supported

Posted on by

29.11.2012 RIFF JTAG – HTC HD Mini T5555 (HTC Photon) Unbrick, Unlock, IMEI, CID repair supported

Repairing bricked HTC HD Mini is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB9210000’.
Currently supported resurrection for NAND memories with 2KB page size.

To resurrect HTC HD Mini:

  •  Solder JTAG cable to HTC HD Mini JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC HD Mini is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Posted on by

21.11.2012  RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Repairing bricked HTC OneS is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.09.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4020000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC EVO 4G LTE (HTC Jewel) Unbrick – Dead Boot Repair Supported

Posted on by

16.11.2012    RIFF JTAG – HTC EVO 4G LTE  Unbrick – Dead Boot Repair Supported

Repairing bricked HTC Jewel is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.15.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ7510000’.

To resurrect HTC Jewel:

  •  Solder JTAG cable to HTC Jewel JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Jewel is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Posted on by

13.11.2012 RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Resurrecting HTC WildFireS CDMA is easy with RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 (for NAND chips with 4Kb page size). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG7620000’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS CDMA:

  •  Solder JTAG cable to HTC WildFireS CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC WildFireS CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

.