Tag Archives: Galaxy

RIFF JTAG – Samsung GT-i8190 Galaxy S III Mini Unbrick – Dead boot repair supported

Posted on by

29.03.2013  RIFF JTAG – Samsung GT-i8190 Galaxy S III Mini Unbrick – Dead boot repair supported

Repairing bricked Samsung I8190 is easy with the RIFF Box.
Please note, USB cable must be either disconnected or connected to PC. Charger is not allowed. In order to establish connection, insert battery and press Power On.
Problem to establish JTAG connection means the device is dead up to the loader which enables JTAG. In this case phone must be detected via USB cable as “U8500 USB ROM”. Please install drivers which are located in JTAG Manager “Drivers\NTU8500” folder, leave USB cable connected and start resurrection again.

To resurrect Samsung I8190:

  •  Solder JTAG cable to Samsung I8190 JTAG pads;
  •  Attach battery and connect USB cable;
  •  Make sure Samsung I8190 is selected in the list of models;
  •  Click Resurrect button;
  •  If required, press Power On key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i8190_galaxy_s_iii_mini_2

RIFF JTAG – Samsung GT-S6312 Galaxy Young Duos Unbrick – Dead boot repair supported

Posted on by

09.03.2013 RIFF JTAG – Samsung GT-S6312 Galaxy Young Duos Unbrick – Dead boot repair supported

Repairing bricked Samsung S6312 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S6312:

  •  Solder JTAG cable to Samsung S6312 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S6312 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.
samsung_gt-s6312_galaxy_young_duos

RIFF JTAG – Samsung GT-S5301 Galaxy Pocket Plus Unbrick – Dead Boot repair supported

Posted on by

15.02.2013   RIFF JTAG – Samsung GT-S5301 Galaxy Pocket Plus Unbrick – Dead Boot repair supported

Repairing bricked Samsung S5301 is easy with the RIFF Box. Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S5301:

  •  Solder JTAG cable to Samsung S5301 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S5301 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_pocket_plus

RIFF JTAG – Samsung SHW-M240S Galaxy Ace Unbrick – Dead Boot repair supported

Posted on by

13.02.2013  RIFF JTAG – Samsung SHW-M240S Galaxy Ace Unbrick – Dead Boot repair supported

Repairing bricked Samsung M240S is easy with the RIFF Box. You need to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung M240S do this:

  •  Solder JTAG cable to Samsung M240S JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung M240S is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power On button shortly if it stops on establish conneciton stage;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

.
Samsung-Galaxy-Ace-SHW-M240S

RIFF JTAG – Samsung SHW-M190S GALAXY S Hoppin Unbrick – Dead Boot repair supported

Posted on by

13.02.2013  RIFF JTAG – Samsung SHW-M190S GALAXY S Hoppin Unbrick – Dead Boot repair supported

Repairing bricked Samsung M190S is easy with the RIFF Box. The device is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung M190S:

  •  Solder JTAG cable to Samsung M190S JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Attach battery connector;
  •  Make sure Samsung M190S is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung-m190s-

RIFF JTAG – Samsung GT-S6810P Galaxy Fame WORLD FIRST Boot repair support ! ! !

Posted on by

07.02.2013  RIFF JTAG – Samsung GT-S6810P Galaxy Fame WORLD FIRST Boot repair support ! ! !

Repairing bricked Samsung S6810P is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S6810P:

  •  Solder JTAG cable to Samsung S6810P JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S6810P is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘OK’ keys and press Power-On. And after you see the warning message press ‘Volume Up’ key to enter Download Mode.

.
samsung_gt-s6810_galaxy_fame

RIFF JTAG – Samsung YP-G1CW / YP-G1CB Galaxy S WiFi Unbrick – Dead Boot repair supported

Posted on by

05.02.2013  RIFF JTAG – Samsung YP-G1CW / YP-G1CB Galaxy S WiFi Unbrick – Dead Boot repair supported

Samsung YP-G1 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.

To resurrect Samsung YP-G1:

  •  Solder JTAG cable to Samsung YP-G1 JTAG pads;
  •  Connect microUSB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung YP-G1 is selected in the list of models;
  •  Make sure a fixed TCK frequency is selected;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_yp-g1_galaxy_s_wifi_40

RIFF JTAG – Samsung GT-S7562 Galaxy S Duos Unbrick – Dead Boot repair supported

Posted on by

22.01.2013   RIFF JTAG – Samsung GT-S7562 Galaxy S Duos Unbrick – Dead Boot repair supported

Repairing bricked Samsung S7562 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7562:

  •  Solder JTAG cable to Samsung S7562 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7562 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_galaxy_s_duos_front

RIFF JTAG – Samsung SGH-T879 Galaxy Note Unbrick – Dead Boot repair supported

Posted on by

29.12.2012  RIFF JTAG – Samsung SGH-T879 Galaxy Note Unbrick – Dead Boot repair supported

Repairing bricked Samsung T879 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung T879:

  •  Solder JTAG cable to Samsung T879 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung T879 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
t-mobile-galaxy-note