RIFF JTAG – CDMA Samsung SPH-D700 Galaxy S Epic 4G Unbrick, Dead Boot repair supported

14.03.2011 CDMA Samsung SPH-D700 Galaxy S Epic 4G Unbrick, Dead Boot repair supported

Samsung SPH-D700 is based on the S5PC110 Processor (ARM core is Cortex-A8). Depending on firmware state resurrection can be a bit confusing: for successful connection you will require charged battery. Please note – no matter whether you have USB cable or not – it must not be connected to phone. This is important.
Resurrector will reflash IBL, PBL, SPL and PARAM areas. Additionally you can select KERNEL and RECOVERY partitions to be reflashed too. Though them are required only for recovery mode and not needed for following USB firmware update by Odin software. So if you don’t need recovery mode don’t select these 2 partitions – otherwise you will just waste time waiting for them to be reflashed.
If after resurrection the download mode still cannot be initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung SPH-D700:

  • Solder JTAG cable to Samsung SPH-D700 JTAG pads;
  • Make sure USB cable or charger is not connected;
  • Make sure Samsung SPH-D700 is selected in the list of models;
  • Make sure a fixed TCK frequency is selected;
  • Insert battery;
  • Click Resurrect button;
  • Press Power On key; when you will see “Establish communication with the phone…” message – press Power On ey again (and hold it pressed for 1-2 seconds);
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download or recovery mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘1’ key on the keypad and press Power-On to enter download mode;
  • Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter recovery mode.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung Galaxy TAB (Samsung P1000) Unbrick, Repair dead boot supported

26.11.2010   Samsung Galaxy TAB (Samsung P1000) Unbrick, Repair dead boot supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.

“Samsung_P1000.dll” contains pinout, instructions and required repair files for Samsung Galaxy TAB (Samsung P1000) Unbrick, Repair dead boot.

RIFF JTAG – Samsung i5500 Galaxy Unbrick, Dead boot repair supported

29.10.2010  Samsung i5500 Galaxy Unbrick, Dead boot repair supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Samsung_i5500.dll” contains pinout, instructions and required repair files for Samsung i5500 Galaxy Unbrick, Dead boot repair.

RIFF JTAG – Samsung i897 Captivate Galaxy S Unbrick, Dead boot repair, Download mode activation supported

27.10.2010  Samsung i897 Captivate Galaxy S Unbrick, Dead boot repair, Download mode activation supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Samsung_i897.dll” contains pinout, instructions and required repair files for Samsung i897 Captivate Galaxy S Unbrick, Dead boot repair and Download mode activation.

RIFF JTAG – Samsung T959 Vibrant Galaxy S Unbrick bricked boot supported

18.10.2010   Samsung T959 Vibrant Galaxy S Unbrick bricked boot supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.

“Samsung_t959.dll” contains pinout, repair instructions and required files for single click Samsung Vibrant Galaxy S – T959 Unbrick/Repair bricked boot.

RIFF JTAG – Samsung Galaxy S i9000 Unbrick/repair bricked boot

15.09.2010 Samsung Galaxy S – i9000 unbricking supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.

“Samsung_i9000.dll” contains pinout, repair instructions and required files for single click Samsung Galaxy S – i9000 Unbrick/Repair bricked boot.

RIFF JTAG – Samsung I5700 Galaxy Lite Unbrick/Repair dead boot supported

02.09.2010  Samsung I5700 Galaxy Lite Unbrick/Repair dead boot supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Samsung_i5700_PDA.dll” contains pinout, repair instructions and required files for single click Samsung I5700 Galaxy Lite Unbrick/Repair dead boot.

RIFF JTAG – Unbrick Samsung i7500 Galaxy, repair dead boot

16.08.2010 RIFF JTAG – Samsung  i7500 unbrick, dead boot repair


Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL-s, download it and restart the software.
“Samsung_i7500.dll” contains pinout, repair instructions and required repair files for Samsung  Galaxy i7500 unbrick, dead boot repair.