Tag Archives: Firmware

RIFF JTAG – CDMA Motorola w210 supported

Posted on by

16.12.2011 CDMA Motorola w210 supported

Resurrecting Motorola W210 is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0089/0x8855

To resurrect Motorola W210:

  •  Solder JTAG cable to Motorola W210 JTAG pads;
  •  Connect charger for auto power on or use battery;
  •  Make sure Motorola W210 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;
_

RIFF JTAG – CDMA Samsung B209 Breeze Supported

Posted on by

03.10.2011   CDMA Samsung B209 Breeze Supported

Resurrecting Samsung B209 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2256

To resurrect Samsung B209:

  •  Solder JTAG cable to Samsung B209 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung B209 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

RIFF JTAG – CDMA Sungil SXC1080 Modem supported

Posted on by

30.09.2011   CDMA Sungil SXC1080 Modem supported

 

Resurrecting Sungil SXC1080 is simple.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x22E0

To resurrect Sungil SXC1080:

  •  Solder JTAG cable to Sungil SXC1080 JTAG pads;
  •  Attach battery or external power supply;
  •  Make sure Sungil SXC1080 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

RIFF JTAG – CDMA LG TD636 Unbrick – Boot repair supported

Posted on by

30.08.2011  CDMA LG TD636 Unbrick – Boot repair supported

Resurrecting LG TD636 is simple. To establish connector battery or external power supply must be connected and Power On key to be pressed.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0x2202

To resurrect LG TD636:

  •  Solder JTAG cable to LG TD636 JTAG pads;
  •  Attach battery or external power supply;
  •  Make sure LG TD636 is selected in the list of models;
  •  Press Power On key;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – JTAG Manager v1.33, RIFF Box firmware v1.25 released

Posted on by

RIFF Box Firmware 1.25
—————————

  • Added 5.0V USB Power On/Off controlling feature
  • Changed sequence for 32-bit write accesses for ARM11 core (MSM8xxx support)

JTAG Manager 1.33
—————————

  • Improved connection policy:
  • Resurrection/DCC connection to device is implemented in such way that JTAG speed changes have 2 stages – booting stage and working stage.
    Booting stage is the one from the connection start and until the DCC Loader upload is complete. Booting TCK/RTCK speed are setup by JTAG Manager no matter what are the TCK settings by user (JTAG TCK Speed field in the JTAG Manager). Booting speed is hardcoded in the DLL.
    After “booting” stage is complete, the “working” speed is set – the one which is selected by user in the JTAG TCK Speed field.
    If Booting Speed in resurrector DLL is hardcoded as ‘RTCK’ the JTAG Manager would always use RTCK mode during booting stage.
  • Now policy is changed that is when user selects a fixed TCK frequency the JTAG Manager will automatically change booting speed to the fixed TCK too.
  • Fixed bug: if “Use End Address” and “AutoFull Flash Size” were checked there was error setting valid length to read.
  • For Advanced Users: advanced settings are now moved from the DCC Read/Write page (“Notifications…”) into separate button on Box Service page (Advanced Settings button)
  • Added 5.0V USB Power On/Off controlling feature
  • For this go to Box Service page, click Advanced Settings: the Notifications dialog will be displayed, go to “Advanced Settings” page and set desired mode for “Enable 5.0V output” checkbox.
  • When enabled, 5.0V power will be on after any “JTAG” operation executed and will remain “ON” until box restart or until “Enable 5.0V output” checkbox is unchecked and any “JTAG” operation is executed.
  • Added optimization for flashing memory devices which are sector-based (like MDOC H3 or MMC/SD memory cards) if error code 0x3C (write-protect) is received no recover attempts are made.

RIFF JTAG – CDMA Huawei C5589 Unbrick – Boot repair supported

Posted on by

13.05.2011   CDMA Huawei C5589 Unbrick – Boot repair supported

Resurrecting Huawei C5589 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0x2230

To resurrect Huawei C5589:

  • Solder JTAG cable to Huawei C5589 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Huawei C5589 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE C370 Repair supported

Posted on by

22.04.2011  CDMA ZTE C370 Repair supported

Resurrecting ZTE C370 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0098/0x0096

To resurrect ZTE C370:

  • Solder JTAG cable to ZTE C370 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure ZTE C370 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C6000 Repair supported

Posted on by

22.04.2011   CDMA Haier C6000 Repair supported

Resurrecting Haier C6000 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0x2210

To resurrect Haier C6000:

  • Solder JTAG cable to Haier C6000 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C6000 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C5100 Repair supported

Posted on by

22.04.2011  CDMA Haier C5100 Repair supported

Resurrecting Haier C5100 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C5100:

  • Solder JTAG cable to Haier C5100 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C5100 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Haier C2040 Repair supported

Posted on by

22.04.2011  CDMA Haier C2040 Repair supported

Resurrecting Haier C2040 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C2040:

  • Solder JTAG cable to Haier C2040 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Haier C2040 is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.