Tag Archives: Cdma

RIFF JTAG – CDMA Samsung B159 Boot repair supported

Posted on by

06.04.2011   CDMA Samsung B159 Boot repair supported

Resurrecting Samsung B159 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x57FFFF).

To resurrect Samsung B159:

  • Solder JTAG cable to Samsung B159 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Samsung B159 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA QUALCOMM QSC1100 Generic DLL released

Posted on by

06.04.2011    CDMA QUALCOMM QSC1100 Generic DLL released

Resurrector QSC1100 X14 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU’s internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.

Initial H/W init sequence will setup MCU’s PLL with these parameters:

  • Clock Multiplier = 0x14

Since few different versions of QSC1100 resurrector may exist (with different multiplier values) you may select the one which suits best to your device.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Huawei C2830 Boot repair supported

Posted on by

06.04.2011    CDMA Huawei C2830 Boot repair supported

Resurrecting Huawei C2830 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Since the JTAG test points are placed under keyboard sticker we recommend using USB data cable to supply power to the device.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x5FFFFF).
Please note: if you do not have JIG (that is you solder wires instead) then black graphite covering has to be carefully scratched off in order to access copper surface of the pads.

To resurrect Huawei C2830:

  • Solder JTAG cable to Huawei C2830 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Huawei C2830 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Micromax C111 Boot repair supported

Posted on by

06.04.2011  CDMA Micromax C111 Boot repair supported

Resurrecting Micromax C111 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
There are 2 different hardware revisions of this phone – one is based on Qualcomm QSC1100 MCU and other – is Qualcomm QSC6010 MCU. Current resurrector shall be selected if you have QSC1100 revision.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x6FFFFF).

To resurrect Micromax C111:

  • Solder JTAG cable to Micromax C111 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Micromax C111 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Samsung SPH-D700 Galaxy S Epic 4G Unbrick, Dead Boot repair supported

Posted on by

14.03.2011 CDMA Samsung SPH-D700 Galaxy S Epic 4G Unbrick, Dead Boot repair supported

Samsung SPH-D700 is based on the S5PC110 Processor (ARM core is Cortex-A8). Depending on firmware state resurrection can be a bit confusing: for successful connection you will require charged battery. Please note – no matter whether you have USB cable or not – it must not be connected to phone. This is important.
Resurrector will reflash IBL, PBL, SPL and PARAM areas. Additionally you can select KERNEL and RECOVERY partitions to be reflashed too. Though them are required only for recovery mode and not needed for following USB firmware update by Odin software. So if you don’t need recovery mode don’t select these 2 partitions – otherwise you will just waste time waiting for them to be reflashed.
If after resurrection the download mode still cannot be initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung SPH-D700:

  • Solder JTAG cable to Samsung SPH-D700 JTAG pads;
  • Make sure USB cable or charger is not connected;
  • Make sure Samsung SPH-D700 is selected in the list of models;
  • Make sure a fixed TCK frequency is selected;
  • Insert battery;
  • Click Resurrect button;
  • Press Power On key; when you will see “Establish communication with the phone…” message – press Power On ey again (and hold it pressed for 1-2 seconds);
  • Wait till software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download or recovery mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘1’ key on the keypad and press Power-On to enter download mode;
  • Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On to enter recovery mode.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Huawei C5005 Unbrick – Repair supported

Posted on by

11.03.2011  CDMA Huawei C5005 Unbrick – Repair supported

Resurrecting Huawei C5005 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0xBFFFFF).

To resurrect Huawei C5005:

  • Solder JTAG cable to Huawei C5005 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure Huawei C5005 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE F285 Repair supported

Posted on by

10.03.2011 CDMA ZTE F285 Repair supported

Resurrecting ZTE F285 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x60FFFF).
To resurrect ZTE F285:

  • Solder JTAG cable to ZTE F285 JTAG pads;
  • Insert USB Data cable into board and PC;
  • Make sure ZTE F285 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Huawei C2906 Boot repair supported

Posted on by

16.02.2011   CDMA Huawei C2906 Boot repair supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Huawei_C2906.dll” contains pinout, instructions and required repair files for CDMA Huawei C2906 Boot repair, and NOR flash read/write operations.

RIFF JTAG – CDMA Update Haier C2076 Boot repair supported

Posted on by

24.01.2011  CDMA Update Haier C2076 Boot repair supported

Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Haier_C2076.dll” contains pinout, instructions and required repair files for Haier C2076 Boot repair Unbrick, Dead Boot repair.