Tag Archives: Cable Board

RIFF JTAG – CDMA Olive C2110 Supported

Posted on by

27.12.2011    CDMA Olive C2110 Supported

Resurrecting Olive C2110 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2254

To resurrect Olive C2110:

  •  Solder JTAG cable to Olive C2110 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Olive C2110 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Samsung B339 Breeze Supported

Posted on by

23.12.2011 CDMA Samsung B339 Breeze Supported

Resurrecting Samsung B339 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2256

To resurrect Samsung B339:

  •  Solder JTAG cable to Samsung B339 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung B339 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Huawei C3500 Supported

Posted on by

23.12.2011    CDMA Huawei C3500 Supported 

Resurrecting Huawei C3500 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Huawei C3500:

  •  Solder JTAG cable to Huawei C3500 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Huawei C3500 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Huawei C2856 Supported

Posted on by

22.11.2011  CDMA Huawei C2856 Supported

Resurrecting Huawei C2856 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0020/0x88C0

To resurrect Huawei C2856:

  •  Solder JTAG cable to Huawei C2856 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Huawei C2856 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

_

RIFF JTAG – CDMA Haier C301R supported

Posted on by

20.12.2011   CDMA Haier C301R supported

Resurrecting Haier C301R is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x257E

To resurrect Haier C301R:

  •  Solder JTAG cable to Haier C301R JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Haier C301R is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

RIFF JTAG – LG P999 G2X (LG Star) Modem unbrick/repair supported

Posted on by

19.11.2011  LG P999 G2X (LG Star) Modem unbrick/repair supported

Resurrecting LG P999 Modem part is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC while battery is inside; sometimes during connection pressing Power On key may be required.

To resurrect LG P999 Modem Part:

  •  Solder JTAG cable to LG P999 Modem JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG P999 Modem is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

 

RIFF JTAG – CDMA Samsung B209 Breeze Supported

Posted on by

03.10.2011   CDMA Samsung B209 Breeze Supported

Resurrecting Samsung B209 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0x2256

To resurrect Samsung B209:

  •  Solder JTAG cable to Samsung B209 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung B209 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

RIFF JTAG – LG GM730 Unbrick – Boot repair supported

Posted on by

30.08.2011  LG GM730 Unbrick – Boot repair supported

Resurrecting LG GM730 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).

To resurrect LG GM730:

  •  Solder JTAG cable to LG GM730 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG GM730 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume down’ and ‘Volume up’ keys and press ‘Power ON’ button. In few seconds you should see emergency mode screen.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported

Posted on by

02.08.2011   Sony Ericsson Xperia X8a (SE Shakira) Unbrick – Boot repair supported

Resurrecting SE X8 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X8:

  •  Solder JTAG cable to SE X8 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE X8 is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

 

 

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Sony Ericsson Xperia X10a mini / E10a (SE Robyn) Unbrick – Boot repair supported

Posted on by

02.08.2011    Sony Ericsson Xperia X10a mini / E10a (SE Robyn) Unbrick – Boot repair supported

Resurrecting SE X10 Mini is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.
To resurrect SE X10 Mini:

  •  Solder JTAG cable to SE X10 Mini JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure SE X10 Mini is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.