Tag Archives: Battery Press

RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Posted on by

21.11.2012  RIFF JTAG – HTC One S Z560E (HTC Ville C) Unbrick – Dead Boot Repair Supported

Repairing bricked HTC OneS is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.09.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ4020000’.

To resurrect HTC OneS:

  •  Solder JTAG cable to HTC OneS JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneS is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC Amaze 4G (HTC Ruby) Unbrick – Dead Boot Repair Supported

Posted on by

20.11.2012  RIFF JTAG – HTC Amaze 4G (HTC Ruby) Unbrick – Dead Boot Repair Supported

Repairing bricked HTC Amaze4G is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 1.90.0008. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH8511000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC Amaze4G:

  •  Solder JTAG cable to HTC Amaze4G JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC Amaze4G is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – HTC EVO 4G LTE (HTC Jewel) Unbrick – Dead Boot Repair Supported

Posted on by

16.11.2012    RIFF JTAG – HTC EVO 4G LTE  Unbrick – Dead Boot Repair Supported

Repairing bricked HTC Jewel is easy with the RIFF Box.
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.15.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ7510000’.

To resurrect HTC Jewel:

  •  Solder JTAG cable to HTC Jewel JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC Jewel is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Huawei Ideos U8150/U8150D Unbrick – Boot Repair Supported

Posted on by

16.11.2012  RIFF JTAG – Huawei Ideos U8150/U8150D Unbrick – Boot Repair Supported

Resurrecting Huawei U8150 is simple.
Connection can be established with charger connected while battery is inside.

To resurrect Huawei U8150:

  •  Solder JTAG cable to Huawei U8150 JTAG pads;
  •  Connect Huawei U8150 tablet’s charger for power;
  •  Make sure Huawei U8150 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Huawei Ascend Y200 (Huawei U8655) Unbrick – Dead Boot Repair Supported

Posted on by

16.11.2012  RIFF JTAG – Huawei Ascend Y200 (Huawei U8655) Unbrick – Dead Boot Repair Supported

Resurrecting Huawei U8655 is simple with RIFF Box.
Connection can be established with charger connected while battery is inside.

To resurrect Huawei U8655:

  •  Solder JTAG cable to Huawei U8655 JTAG pads;
  •  Connect Huawei U8655 tablet’s charger for power;
  •  Make sure Huawei U8655 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-i8530 Galaxy Beam Unbrick – Dead Boot Repair Supported

Posted on by

16.11.2012 RIFF JTAG – Samsung GT-i8530 Galaxy Beam Unbrick – Dead Boot Repair SupportedĐ

Repairing bricked Samsung I8530 is easy with the RIFF Box.
Please note, if you have problems connecting phone, then make sure USB Cable is disconnected, insert battery and press Power On and try connecting again.

To resurrect Samsung I8530:

  •  Solder JTAG cable to Samsung I8530 JTAG pads;
  •  Attach battery;
  •  Disconnect USB Cable (if was connected);
  •  Make sure Samsung I8530 is selected in the list of models;
  •  Click Resurrect button;
  •  If required, press Power On key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung GT-i8350 Omnia W Unbrick – Dead Boot Repair Supported

Posted on by

14.11.2012   RIFF JTAG – Samsung GT-i8350 Omnia W Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung I8350 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.

To resurrect Samsung I8350:

  •  Solder JTAG cable to Samsung I8350 JTAG pads;
  •  Make sure Samsung I8350 is selected in the list of models;
  •  Insert battery and connect USB Data cable;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.

.

RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Posted on by

13.11.2012 RIFF JTAG – HTC Wildfire S CDMA (HTC Marvel C) Unbrick – Dead Boot Repair and full Support

Resurrecting HTC WildFireS CDMA is easy with RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 (for NAND chips with 4Kb page size). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG7620000’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.

To resurrect HTC WildFireS CDMA:

  •  Solder JTAG cable to HTC WildFireS CDMA JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC WildFireS CDMA is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

.

RIFF JTAG – HTC Flyer 4G P515E Unbrick, IMEI, SuperCID, ModelID repair supported

Posted on by

02.11.2012   RIFF JTAG – HTC Flyer 4G P515E Unbrick, IMEI, SuperCID, ModelID repair supported

Repairing bricked HTC Flyer4G (PG4130000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Flyer4G (PG4130000) boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so if DBL area is damanged and MCU has JTAG Disable FUSE blown then there is no way to resurrect your phone via JTAG interface. However, in this case you may use HTC Flyer4G (PG4130000) USB DLL version which does not require JTAG interface and does resurrection procedure via USB cable.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL to 1.14.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG413****’.

To resurrect HTC Flyer:

  •  Solder JTAG cable to HTC Flyer JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Flyer4G (PG4130000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-i9070 Galaxy S Advance Unbrick – Dead Boot Repair Supported

Posted on by

18.10.2012  RIFF JTAG – Samsung GT-i9070 Galaxy S Advance Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung I9070 is easy with the RIFF Box.
Please note, if you have problems connecting phone, then make sure USB Cable is disconnected, insert battery and press Power On and try connecting again.

To resurrect Samsung I9070:

  •  Solder JTAG cable to Samsung I9070 JTAG pads;
  •  Attach battery;
  •  Disconnect USB Cable (if was connected);
  •  Make sure Samsung I9070 is selected in the list of models;
  •  Click Resurrect button;
  •  If required, press Power On key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.