Tag Archives: Auto Power

RIFF JTAG – CDMA Motorola w210 supported

Posted on by

16.12.2011 CDMA Motorola w210 supported

Resurrecting Motorola W210 is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x0089/0x8855

To resurrect Motorola W210:

  •  Solder JTAG cable to Motorola W210 JTAG pads;
  •  Connect charger for auto power on or use battery;
  •  Make sure Motorola W210 is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;
_

RIFF JTAG – CDMA Samsung S239 (MPower) Repair supported

Posted on by

26.04.2011  CDMA Samsung S239 (MPower) Repair supported

Resurrecting Samsung S239 is simple. Phone is auto powered on with USB Cable connected; battery presence is not required.

To resurrect Samsung S239:

  • Solder JTAG cable to Samsung S239 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Samsung S239 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Motorola W150i (MSM6000) Repair supported

Posted on by

21.04.2011   CDMA Motorola W150i (MSM6000) Repair supported

Resurrecting Motorola W150i is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.

To resurrect Motorola W150i:

  • Solder JTAG cable to Motorola W150i JTAG pads;
  • Connect charger for auto power on or use battery;
  • Make sure Motorola W150i is selected in the list of models;
  • Click Resurrect button;
  • Choose which areas to flash;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Samsung SCH-S109 (MSM6000) Repair supported

Posted on by

20.04.2011  CDMA Samsung SCH-S109 (MSM6000) Repair supported

Resurrecting Samsung S109 is simple. Phone is auto powered on with charger connected; battery presence is not required.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x3FFFFF).

To resurrect Samsung S109:

  • Solder JTAG cable to Samsung S109 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Samsung S109 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA ZTE Striker (S1602) Boot Repair supported

Posted on by

12.04.2011  CDMA ZTE Striker (S1602) Boot Repair supported

Resurrecting ZTE S1602 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x87FFFF).

To resurrect ZTE S1602:

  • Solder JTAG cable to ZTE S1602 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure ZTE S1602 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Samsung B159 Boot repair supported

Posted on by

06.04.2011   CDMA Samsung B159 Boot repair supported

Resurrecting Samsung B159 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x57FFFF).

To resurrect Samsung B159:

  • Solder JTAG cable to Samsung B159 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Samsung B159 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – CDMA Micromax C111 Boot repair supported

Posted on by

06.04.2011  CDMA Micromax C111 Boot repair supported

Resurrecting Micromax C111 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
There are 2 different hardware revisions of this phone – one is based on Qualcomm QSC1100 MCU and other – is Qualcomm QSC6010 MCU. Current resurrector shall be selected if you have QSC1100 revision.
Resurrector re-flashes only firmware zone of the phone (0x000000 to 0x6FFFFF).

To resurrect Micromax C111:

  • Solder JTAG cable to Micromax C111 JTAG pads;
  • Connect ignition cable for auto power on or use battery;
  • Make sure Micromax C111 is selected in the list of models;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.