Tag Archives: Ace

RIFF JTAG – Samsung GT-S7500 Galaxy Ace Plus Unbrick – Boot Repair supported, World First ! ! !

Posted on by

28.02.2012      Samsung GT-S7500 Galaxy Ace Plus Unbrick – Boot Repair supported, World First !  !  !

Resurrecting Samsung S7500 is easy.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7500:

  •  Solder JTAG cable to Samsung S7500 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7500 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair

Posted on by

16.06.2011   RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair

Resurrecting HTC Desire HD is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Desire HD boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to 0.85.0007 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD9810000’.
There is option to reflash BOOT and RECOVERY zones. If selected, then ClockworkMod Recovery v3.0.2.8 will be flashed.

Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Desire HD:

  • Solder JTAG cable to HTC Desire HD JTAG pads;
  • Insert batter and connect USB Data cable;
  • Make sure HTC Desire HD is selected in the list of models;
  • If you use only battery, press Power On key;
  • Click Resurrect button;
  • Wait till software signals a successful operation completion;
  • Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold ‘Volume Down’ key and press ‘Power ON’ button

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG – Samsung Galaxy Ace S5830 Unbrick – Boot repair supported

Posted on by

12.05.2011 Samsung Galaxy Ace S5830 Unbrick – Boot repair supported

Samsung S5830 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5830 do this:

  • Solder JTAG cable to Samsung S5830 JTAG pads;
  • Insert battery and connect USB cable to phone and PC;
  • Make sure Samsung S5830 is selected in the list of models;
  • Click Resurrect button;
  • Wait few seconds until software signals a successful operation completion;
  • Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  • Disconnect PC cable;
  • Insert battery;
  • Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.