Tag Archives: Ace

RIFF JTAG – Samsung Galaxy Ace Duos I589 Unbrick – dead boot repair supported

Posted on by

28.09.2013 RIFF JTAG – Samsung Galaxy Ace Duos I589 Unbrick – dead boot repair supported

Repairing bricked Samsung I589 is easy with the RIFF Box. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung I589 do this:

  •  Solder JTAG cable to Samsung I589 JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung I589 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
.
samsung-galaxy-ace-duos-sch-i589-400x365

RIFF JTAG – Samsung GT-S7500T Galaxy Ace Plus Unbrick – Dead boot repair supported

Posted on by

19.04.2013 RIFF JTAG – Samsung GT-S7500T Galaxy Ace Plus Unbrick – Dead boot repair supported

Resurrecting Samsung S7500T is easy with RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7500T:

  •  Solder JTAG cable to Samsung S7500T JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7500T is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

samsung_ace_plus

RIFF JTAG – Samsung SHW-M240S Galaxy Ace Unbrick – Dead Boot repair supported

Posted on by

13.02.2013  RIFF JTAG – Samsung SHW-M240S Galaxy Ace Unbrick – Dead Boot repair supported

Repairing bricked Samsung M240S is easy with the RIFF Box. You need to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung M240S do this:

  •  Solder JTAG cable to Samsung M240S JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung M240S is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power On button shortly if it stops on establish conneciton stage;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

.
Samsung-Galaxy-Ace-SHW-M240S

RIFF JTAG – Samsung GT-S6802 Galaxy Ace Duos Unbrick – Dead Boot Repair Supported

Posted on by

02.11.2012   RIFF JTAG – Samsung GT-S6802 Galaxy Ace Duos Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung S6802 is easy with the RIFF Box. Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S6802:

  •  Solder JTAG cable to Samsung S6802 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S6802 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung GT-S5830L Galaxy Ace Unbrick – Dead Boot Repair Supported

Posted on by

19.10.2012   RIFF JTAG – Samsung GT-S5830L Galaxy Ace Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung S5830L is easy with the RIFF Box. You need to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5830L do this:

  •  Solder JTAG cable to Samsung S5830L JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung S5830L is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power On button shortly if it stops on establish conneciton stage;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

.

RIFF JTAG – Samsung GT-i8160 Galaxy Ace 2 Unbrick – Dead Boot Repair Supported

Posted on by

18.10.2012   RIFF JTAG – Samsung GT-i8160 Galaxy Ace 2 Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung I8160 is easy with the RIFF Box.
Please note, USB cable must be disconnected. In order to establish connection, insert battery and press Power On.

To resurrect Samsung I8160:

  •  Solder JTAG cable to Samsung I8160 JTAG pads;
  •  Attach battery;
  •  Disconnect USB Cable (if was connected);
  •  Make sure Samsung I8160 is selected in the list of models;
  •  Click Resurrect button;
  •  If required, press Power On key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung GT-S5830G Galaxy Ace Unbrick – Dead Boot Repair Supported

Posted on by

10.10.2012    RIFF JTAG – Samsung GT-S5830G Galaxy Ace Unbrick – Dead Boot Repair Supported

Repairing bricked Samsung S5830G is easy with the RIFF Box. You need to hold Power On button during JTAG connection establishing phase.

To resurrect Samsung S5830G do this:

  •  Solder JTAG cable to Samsung S5830G JTAG pads;
  •  Insert battery and connect USB cable to phone and PC;
  •  Make sure Samsung S5830G is selected in the list of models;
  •  Click Resurrect button;
  •  Press Power On button shortly if it stops on establish conneciton stage;
  •  Wait few seconds until software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

.

RIFF JTAG – Samsung GT-S7500L Galaxy Ace Plus Unbrick – Dead Boot repair

Posted on by

14.09.2012  RIFF JTAG – Samsung GT-S7500L Galaxy Ace Plus Unbrick – Dead Boot repair

Resurrecting Samsung S7500L is easy with RIFF box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7500L:

  •  Solder JTAG cable to Samsung S7500L JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7500L is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – HTC via USB Cable Support added

Posted on by

24.04.2012  RIFF JTAG – HTC via USB Cable Support added

Whats new:
Released support for HTC phones based on MSM8x55 CPU, which are enumerated on USB port as “QHUSB_DLOAD” device. Now it’s possible to repair these phones without soldering any wires. Even without opening !

Following models are supported at the moment:

  • HTC Desire HD (HTC Ace)
  • HTC Desire S (HTC Saga)
  • HTC Desire Z (HTC Vision)
  • HTC Flyer 3G
  • HTC Flyer WiFi
  • HTC Evo View 4G
It is possible to force QHUSB_DLOAD mode by disabling Vdd line on eMMC chip. Check Desire S TP info for example. This means, You can work with any MSM8255/MSM8655 based HTC phone, as long as You force it into QHUSB_DLOAD mode.
Follow this procedure if You want to use these updates:
  • Connect Your phone to USB port and install QHUSB_DLOAD device driver (C:\Program Files (x86)\RIFF Box JTAG Manager\Drivers\32Bit\QDLOADER)
  • Launch JTAG Manager, select appropriate Model DLL and click desired button
  • Install “RIFF Box DCCLoader USB Interface” port driver (C:\Users\Admin\Desktop\Drivers_64Bit_WorkedForMe\Drivers\64Bit\DCCLDR)
  • If required, repeat the procedure (sometimes required if device is connected for first time)

We will release USB support for rest of the models on these CPU-s in following days.

To download and install new updates – simply click “Check for Updates” button on Box Service TAB.

RIFF JTAG – Samsung Galaxy Ace – GT-S5830i Unbrick – Boot Repair supported

Posted on by

03.04.2012   RIFF JTAG – Samsung GT-S5830i Unbrick – Boot Repair supported

Repairing bricked Samsung GT-S5830i is easy with RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5830i:

  •  Solder JTAG cable to Samsung S5830i JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung S5830i is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
  •  If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

.