16.02.2011 Atmel AT91SAM9263-EK NAND Interface supported
Resurrector AT91SAM9263-EK contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of ATMEL AT91SAM9263 MCU’s internal RAM memory.
Loader has full (read/write) access to AT91SAM9263-EK evaluation board’s NAND memory.
Currently only the 8-bit NAND interface is implemented.
16.02.2011 HTC HD7 Unbrick, Unlock, IMEI Repair and CID Update supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“HTC_HD7.dll” contains pinout, instructions and required repair files for HTC HD7 Unbrick, Unlock, IMEI Repair and CID Update.
16.02.2011 CDMA Huawei C2906 Boot repair supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Huawei_C2906.dll” contains pinout, instructions and required repair files for CDMA Huawei C2906 Boot repair, and NOR flash read/write operations.
10.02.2011 LG P500 Optimus One Unbrick, Dead boot repair supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“LG_P500.dll” contains pinout, instructions and required repair files for LG P500 Optimus One Unbrick, Dead boot repair.
10.02.2011 RIFF JTAG Manager v1.24, RIFF Box Firmware v1.18
Firmware 1.18
—————————
– PXA270 debug is now available in ARM/Thumb modes (use the GDBServer for this);
JTAG Manager 1.24
—————————
– In case when Resurrector has no DCC Loader the JTAG Manager will now report it correctly and will not allow DCC Read/Write features
– (SDK): more functions are now available (exported) for future Resurrector DLLs;
– Usefull Plugins Enabled
—————————
Qualcom FullFlash Image Processing Tool:
This plugin works with NAND image files which have generic Qualcomm layout
With help of this plugin you can do:
– Disassemble a full NAND image file previously obtained with JTAG Manager (DCC Read/Write Page);
– Inspect each partition contents (main zone and spare zone) simultaneously;
– Save separate partitions to HDD (only main zone, only spare zone, or both zones);
– Write a chosen partition directly into phone;
– Read a chosen partition directly from the phone and substitute old partition contents to new ones;
Please note, direct read/write operations from/to the phone will require proper resurrector to be set (Resurrector Settings: thus before clicking the Activate Plugin button make sure compatible model is selected as well as other settings like TCK/RTCK frequencies).
You can access it from “Usefull Plugins” TAB :
09.02.2011 LG GT540 Optimus Unbrick – Repair Boot supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“LG_GT540.dll” contains pinout, instructions and required repair files for LG GT540 Optimus Unbrick – Repair Dead Boot.
08.02.2011 Hewlett-Packard iPAQ 614 Boot Repair/Unbrick supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“iPak_614.dll” contains pinout, instructions and required repair files for Hewlett-Packard iPAQ 614 Boot Repair/Unbrick.
07.02.2011 RIFF Box JTAG Manager v1.23, RIFF Box firmware v1.17
Firmware 1.17
—————————
* Optimized DCC transfers (debugger-to-target) for ARM9 cores (~64,3% speed increase)
* Added RX-polling feature (debugger-to-target) for ARM9 DCC transfers.
RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for ARM9 target to be ready to accept next packet over DCC: this feature slows down a little the JTAG-to-ARM9 DCC transfers but guaranties no packets loss for slow clocked targets;
JTAG Manager 1.23
—————————
* Improved DCC flashing functionality (for DCC Loaders that work in targets with a small RAM capacity);
* Added 4 very low RTCK Sampling frequencies (20kHz, 40kHz, 60kHz and 80kHz) for some extreme cases
* Fixed another bug in the optimized DLL loading scheme;
* Increased ERASE waiting timeout (for slow NOR flash chips) so now erase operation for such chips will go successully and will not result in erase timeout
* Added “Usefull plugins” page;
“Usefull Plugins” will be new feature, we hope to release first one during this week. So stay tuned.
As usually, click the “Check for Updates” button to obtain latest files.
31.01.2011 ZTE MF190 Broadband modem Unbrick, Dead boot repair supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“ZTE_MF190.dll” contains pinout, instructions and required repair files for ZTE MF190 Broadband modem Unbrick, Dead boot repair.
28.01.2011 Dell Streak (Dell Mini 5) Unbrick – Repair dead boot supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Dell_Streak.dll” contains pinout, instructions and required repair files for Dell Streak (Dell Mini 5) Unbrick – Repair dead boot.
