RIFF JTAG – HTC Flyer (PG41100) Unbrick, Unlock, IMEI, S-off, update supported

Posted on by

06.04.2012  RIFF JTAG – HTC Flyer (PG41100) Unbrick, Unlock, IMEI, S-off, update supported

Repairing bricked HTC Flyer (PG41100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Some (or all) revisions of HTC Flyer boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the DBL loader, so writing to DBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into DBL zone and will respond with success code as if flashing succeeded. In this way DBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except DBL area) and will re-write PDA’s SPL to 1.11.0003 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG4110000’.
There is option to reflash android BOOT and RECOVERY zones. Recovery zone is flashed with ClockworkMod Recovery 4.0.1.4. In addition, you can set S-OFF (unlock HBOOT so you will be able to flash any ROM) by clicking “Make S-OFF” checkbox in the resurrector settings.
Sometimes (for example after rooting attempts) phone has a modified DBL loader (which may not accept official HTC boot files). To restore phone functionality you need to reflash DBL loader. There is option to reflash DBL code (DBL area will be temporary unlocked for reflashing). But please note, reflashing DBL area is very dangerous, since in case flashing stops in the middle, you will have briked phone with permanently disabled JTAG interface.
Please note, if your phone has the DBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.

To resurrect HTC Flyer:

  •  Solder JTAG cable to HTC Flyer JTAG pads;
  •  Insert battery and connect USB Data cable;
  •  Make sure HTC Flyer is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods. You can use CWM recovery to flash any ZIP file – for this during resurrection add BOOT & RECOVERY zones to be resurrected too.
.

RIFF JTAG – STB Orton 4100C Unbrick supported

Posted on by

06.04.2012    RIFF JTAG – STB Orton 4100C Unbrick supported

Repairing bricked Orton 4100C is easy with the RIFF Box. Receiver is based on the ALI M3329C processor. Receiver is powered on when power plug is attached. If connection process stops at “Establish communication with the phone…” just reset the receiver’s power.
Current resurrector contains Boot, Firmware and Data zones which in total is complete full connects for 2Mb SPI serial memory chip.
Please note, to enable JTAG you have to make sure the JP1 jumper on board is not shorted. Sometimes you may need to disconnect front LED panel interface cable from the board (13-pin connector). After resurrection do not forget to solder the resistor back or shortcut JP1 jumper.
To resurrect Orton 4100C:

  •  Solder JTAG cable to Orton 4100C JTAG pads;
  •  Make sure Orton 4100C is selected in the list of models;
  •  Connect power;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now receiver is in bootable condition, that is, even if it does not start up normally you can flash it via UART using known flashing methods. Or you can do resurrection checking full clone resurrect option – this will re-write all flash memory contents.
.

RIFF JTAG – STB EuroSky ES-4100 Unbrick supported

Posted on by

06.04.2012   RIFF JTAG – STB EuroSky ES-4100 Unbrick supported

Repairing bricked EuroSky ES-4100 is easy with the RIFF Box. Receiver is based on the ALI M3329C processor. Receiver is powered on when power plug is attached. If connection process stops at “Establish communication with the phone…” just reset the receiver’s power.
Current resurrector contains Boot, Firmware and Data zones which in total is complete full connects for 2Mb SPI serial memory chip.
Please note, to enable JTAG you have to make sure the JP1 jumper on board is not shorted, desolder resistor R65. Sometimes you may need to disconnect front LED panel interface cable from the board (13-pin connector). After resurrection do not forget either to solder the resistor back or shortcut JP1 jumper.

To resurrect EuroSky ES-4100:

  •  Solder JTAG cable to EuroSky ES-4100 JTAG pads;
  •  Make sure EuroSky ES-4100 is selected in the list of models;
  •  Connect power;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now STB is in bootable condition, that is, even if it does not start up normally you can flash it via UART using known flashing methods. Or you can do resurrection checking full clone resurrect option – this will re-write all flash memory contents.
.

RIFF JTAG – Lynksis Router LinkSys WRT54G unbrick supported

Posted on by

06.04.2012 RIFF JTAG – Lynksis Router LinkSys WRT54G unbrick supported
Repairing bricked LinkSys WRT54GL is easy with the RIFF Box. Router is powered on when power plug is attached. If connection process stops at “Establish communication with the phone…” just reset router’s power.
Current resurrector contains Boot, Configuration and Firmware zones for memory chip with ID 0x00C2/0x22A8

To resurrect LinkSys WRT54GL:

  •  Solder JTAG cable to LinkSys WRT54GL JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LinkSys WRT54GL is selected in the list of models;
  •  Click Resurrect button;
  •  Choose which areas to flash;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now router is in bootable condition, that is, even if it does not start up normally you can flash it via UART using known flashing methods. Or you can do resurrection checking full clone resurrect option – this will re-write all flash memory contents.
.

RIFF JTAG – Samsung Galaxy Mini – GT-S5570i Unbrick – Boot repair supported

Posted on by

03.04.2012   RIFF JTAG – Samsung Galaxy Mini – GT-S5570i Unbrick – Boot repair supported
Repairing bricked Samsung S5570i is easy with RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5570i:

  •  Solder JTAG cable to Samsung S5570i JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung S5570i is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
  •  If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

.

RIFF JTAG – Samsung Galaxy Ace – GT-S5830i Unbrick – Boot Repair supported

Posted on by

03.04.2012   RIFF JTAG – Samsung GT-S5830i Unbrick – Boot Repair supported

Repairing bricked Samsung GT-S5830i is easy with RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5830i:

  •  Solder JTAG cable to Samsung S5830i JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung S5830i is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
  •  If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

.

 

RIFF JTAG – eMMC Partition Plugin v1.0 (Qualcomm EBR-MBR based eMMC flash images processing)

Posted on by

RIFF JTAG – eMMC Partition Plugin v1.0 (Qualcomm EBR-MBR based eMMC flash images processing)

This plugin works with eMMC image files which have standard Master Boot Record (MBR) and Extended Boot Record (EBR) formatting. Most of eMMC-bootable mobile phones have their eMMC memory formatted in such style. In this case partitions are accessed in standard way, by Partition ID: for example boot loader partitions or OS image partition (compare with qualcomm MIBIB partitioning: while ‘MIBIB’-type partitions have standalone partition descriptor block which contains info on all partitions and is posistioned in a definite NAND address, the eMMC partitioning is one MBR sector at fixed position + a chain of EBR sectors which are scattered throughout the eMMC address space in a literally random way).
This plugin is a powerfull tool which enormously simplifies resurrection process (providing you have the required boot files from an official firmware or you have a ‘donor’ device) for those devices which are not yet supported by a dedicated resurrector DLL.
Please note, such phones as Samsung Exynos MCU based pohones (for example I9100, P6200, P6800, N7000, I9220 and etc), though have eMMC chip, are not partitioned in MBR way and thus are not the subject for the current plugin. These phones are to be processed by different plugin.

With the help of this plugin you can do:

  •  Disassemble a full (or, since eMMC full image files are too large, a partial) eMMC Image File previously obtained with JTAG Manager (DCC Read/Write Page);
  •  Inspect each partition contents;
  •  Save separate partitions to HDD;
  •  Save all partitions as standalone files to HDD;
  •  Build-up your own full image file: for this you need to read from device (by clicking “Load Image from Device” button) or open from file (by clicking “Load Image from File” button) the eMMC partitioning data and then by selecting desired partitions click “Inject Into Partition” button to upload data from file into selected partition. Then you can save all full image file to HDD or flash injected partitions directly into device;
  •  Write a chosen partition directly into device;
  •  Read a chosen partition directly from device and substitute old partition contents to new ones;
  •  Create eMMC partitioning snapshot (that is storing info on full EBR chain: each EBR sector position).
  •  Restore eMMC partitioning from previously taken file: it is convenient if eMMC memory is erased and all formatting data is lost.
  •  Plugin supports new RIFF™ shrinked binary files format (*.riffpbin): which allows to shrink huge eMMC Image files into small sized-files (for example, Image File for 14GB empty eMMC chip is shrinked into ~10 KByte(!) size), thus HDD space is preserved, while performance is not visibly effected.

Please note, direct read/write operations from/to the device will require proper resurrector to be set (Resurrector Settings: thus before clicking the Activate Plugin button make sure proper model is selected as well as other settings like TCK/RTCK frequencies).
.

RIFF JTAG – HTC 7 Pro (HTC Gold) Unbrick, Unlock, IMEI and CID repair supported

Posted on by

02.04.2012  RIFF JTAG – HTC 7 Pro (HTC Gold) Unbrick, Unlock, IMEI and CID repair supported

Repairing bricked  HTC 7 Pro is easy with RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will re-flash radio’s boot zone and will re-write PDA’s SPL to 0.71.1000 or 0.00.1000 SPL version (depends on your choice). Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC9210000’.

To resurrect HTC 7 Pro:

  •  Solder JTAG cable to HTC 7 Pro JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC 7 Pro is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see TriColor picture.

.

RIFF JTAG – Apple iPhone 4S Unlock via USB cable, World First ! ! !

Posted on by

01.04.2012  RIFF JTAG – Apple iPhone 4S Unlock via USB cable, World First ! ! ! (Fools day edition)

Unlocking network locked iPhone 4s is easy with RIFF Box.

To Unlock iPhone 4s :

  • Connect Apple iPhone 4s to RIFF Box USB port
  • Start RIFF JTAG Manager
  • Select Apple iPhone4s from menu
  • Open “Useful Plugins” TAB
  • Activate iOS5 Plugin
  • Click  “Permanent Unlock” button
  • Smile !

Please click “Check for Updates” button in order to download new updates.