RIFF JTAG – Samsung SGH-P960 Unbrick – Dead Boot Repair Supported

Posted on by

05.10.2012    RIFF JTAG – Samsung SGH-P960 Unbrick – Dead Boot Repair Supported

Resurrecting Samsung P960 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.

To resurrect Samsung P960:

  •  Solder JTAG cable to Samsung P960 JTAG pads;
  •  Make sure Samsung P960 is selected in the list of models;
  •  Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘9’ key and press ‘Power ON’ button. In few seconds phone enters download mode.

.

RIFF JTAG – Samsung SGH-i747M Galaxy S III LTE Unbrick – Boot Repair Supported

Posted on by

03.10.2012    RIFF JTAG – Samsung SGH-i747M Galaxy S III LTE Unbrick – Boot Repair Supported

Repairing bricked Samsung I747M is easy with the RIFF Box.The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung I747M:

  1.  Solder JTAG cable to Samsung I747M JTAG pads;
  2.  Connect USB cable to phone and PC;
  3.  Insert battery;
  4.  Make sure Samsung I747M is selected in the list of models;
  5.  Click Resurrect button;
  6.  Wait till software signals a successful operation completion;
  7.  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.

RIFF JTAG – Samsung SGH-T999V Galaxy S 3 Unbrick – Boot Repair Supported

Posted on by

03.10.2012 RIFF JTAG – Samsung SGH-T999V Galaxy S 3 Unbrick – Boot Repair Supported

Repairing bricked Samsung T999V is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung T999V:

  •  Solder JTAG cable to Samsung T999V JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung T999V is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.

RIFF JTAG – Samsung SGH-iT999 Galaxy S 3 Unbrick – Dead Boot Repair supported

Posted on by

03.10.2012 Samsung SGH-iT999 Galaxy S 3 Unbrick – Dead Boot Repair supported

Repairing bricked Samsung T999 is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung T999:

  •  Solder JTAG cable to Samsung T999 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung T999 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.

RIFF JTAG -Huawei Ideos X1 U8180 (Huawei Gaga) Unbrick – Dead Boot repair

Posted on by

14.09.2012  RIFF JTAG -Huawei Ideos X1 U8180 (Huawei Gaga) Unbrick – Dead Boot repair

Resurrecting Huawei U8180 is simple with RIFF Box.
Connection can be established with charger connected while battery is inside.

To resurrect Huawei U8180:

  •  Solder JTAG cable to Huawei U8180 JTAG pads;
  •  Connect Huawei U8180 tablet’s charger for power;
  •  Make sure Huawei U8180 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Samsung GT-S7500L Galaxy Ace Plus Unbrick – Dead Boot repair

Posted on by

14.09.2012  RIFF JTAG – Samsung GT-S7500L Galaxy Ace Plus Unbrick – Dead Boot repair

Resurrecting Samsung S7500L is easy with RIFF box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7500L:

  •  Solder JTAG cable to Samsung S7500L JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7500L is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Samsung GT-S6102 Galaxy Y Duos Unbrick – Dead Boot repair

Posted on by

14.09.2012   RIFF JTAG – Samsung GT-S6102 Galaxy Y Duos Unbrick – Dead Boot repair

Resurrecting Samsung S6102 is easy with RIFF Box . To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S6102:

  •  Solder JTAG cable to Samsung S6102 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung S6102 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
  •  If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

.

RIFF JTAG – Samsung SHV-E120L Galaxy S II HD Unbrick – Dead boot repair

Posted on by

11.09.2012  RIFF JTAG – Samsung SHV-E120L Galaxy S II HD Unbrick – Dead boot repair

Repairing bricked Samsung E120L is easy with the RIFF Box. The device is based on the 2nd-generation Qualcomm MSM8660 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung E120L:

  •  Solder JTAG cable to Samsung E120L JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung E120L is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.

RIFF JTAG – Samsung SHV-E160L Galaxy Note LTE Unbrick – Boot repair

Posted on by

11.09.2012  RIFF JTAG – Samsung SHV-E160L Galaxy Note LTE Unbrick – Boot repair

Repairing bricked Samsung E160L is easy with the RIFF Box. The device is based on the 2nd-generation Qualcomm MSM8260 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung E160L:

  •  Solder JTAG cable to Samsung E160L JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung E160L is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.

RIFF JTAG – Samsung SGH-A887 Unbrick – Dead boot repair

Posted on by

10.09.2012   RIFF JTAG – Samsung SGH-A887 Unbrick – Dead boot repair

The Samsung A887 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung A887:

  •  Solder JTAG cable to Samsung A887 JTAG pads;
  •  connect USB cable;
  •  Make sure Samsung A887 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.

.