RIFF JTAG – Samsung GT-S7500T Galaxy Ace Plus Unbrick – Dead boot repair supported

Posted on by

19.04.2013 RIFF JTAG – Samsung GT-S7500T Galaxy Ace Plus Unbrick – Dead boot repair supported

Resurrecting Samsung S7500T is easy with RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung S7500T:

  •  Solder JTAG cable to Samsung S7500T JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure Samsung S7500T is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

samsung_ace_plus

RIFF JTAG – Samsung SCH-R530 Galaxy S III LTE Unbrick – Dead boot repair supported

Posted on by

19.04.2013 RIFF JTAG – Samsung SCH-R530 Galaxy S III LTE Unbrick – Dead boot repair supported

Repairing bricked Samsung R530 is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung R530:

  •  Solder JTAG cable to Samsung R530 JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung R530 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

.
samsung_galaxy_s_iii

RIFF JTAG – Samsung S5750e Wave575 Unbrick – Dead boot repair supported

Posted on by

19.04.2013 RIFF JTAG – Samsung S5750e Wave575 Unbrick – Dead boot repair supported

Resurrecting Samsung S5750E is easy with RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5750E:

  •  Solder JTAG cable to Samsung S5750E JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung S5750E is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state. We used MultiLoader 5.64 version.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold both ‘Volume Down’ (on the left side of phone) and ‘Lock’ (right side bottom part) keys and press Power-On.

s5750e

RIFF Box in Space ! Russian astronauts use it on ISS !

Posted on by

01.04.2013   RIFF Box in Space ! Russian astronaut use it on ISS !

We’re proud to announce that RIFF Box is tested in zero gravity environment !
As reported by NASA, Russian onboard computer on ISS lost it’s boot as a result of spoiled Vodka.

They contacted us and we quickly responded (Our coder was working in Baikonur Cosmodrome science center).
Package with RIFF Box and hi quality ribbon cables and JIG-s was launched two days ago from cosmodrome and arrived safelly.

Onboard computer is repaired ok, but there still remains problem with 3D camera.

Check photos bellow:

scene composition: litho, frame 22

.
master

RIFF JTAG – NTT DoCoMo Samsung Galaxy S III LTE SC-06D Unbrick – Dead boot repair supported

Posted on by

29.03.2013 RIFF JTAG – NTT DoCoMo Samsung Galaxy S III LTE SC-06D Unbrick – Dead boot repair supported

Repairing bricked Samsung SC-06D is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung SC-06D:

  •  Solder JTAG cable to Samsung SC-06D JTAG pads;
  •  Connect USB cable to phone and PC;
  •  Insert battery;
  •  Make sure Samsung SC-06D is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press Power-On.

samsung_galaxy_s_iii_lte_sc-06d

RIFF JTAG – HTC Windows Phone 8X (HTC Accord) Unbrick, Dead boot IMEI repair supported

Posted on by

29.03.2013   RIFF JTAG – HTC Windows Phone 8X (HTC Accord) Unbrick, Dead boot IMEI repair supported

Repairing bricked HTC 8X (PM2330000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PM2330000’.

To resurrect HTC 8X (PM2330000):

  •  Solder JTAG cable to HTC 8X (PM2330000) JTAG pads;
  •  Insert batter and connect USB Data cable;
  •  Make sure HTC 8X (PM2330000) is selected in the list of models;
  •  If you use only battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_windows_phone_8x_2

 

RIFF JTAG – HTC EVO Design 4G PH4430(HTC Kingdom) Unbrick, Unlock, IMEI, SuperCID repair supported

Posted on by

29.03.2013  HTC EVO Design 4G PH4430(HTC Kingdom) Unbrick, Unlock, IMEI, SuperCID repair supported

Repairing bricked HTC EvoDesign4G is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zones and will re-write PDA’s SPL to 1.30.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PH4430000’.
There is option to reflash BOOT and RECOVERY zones.

To resurrect HTC EvoDesign4G via USB Cable:

  •  If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
  •  Make sure USB cable is attached to the board and is connected to PC;
  •  Make sure HTC EvoDesign4G via USB is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.
htc_evo_design_4g

RIFF JTAG – LG E405 Optimus L3 Dual Unbrick – Dead boot repair supported

Posted on by

29.03.2013  RIFF JTAG – LG E405 Optimus L3 Dual Unbrick – Dead boot repair supported

Repairing bricked LG E405 with the RIFF Box is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E405:

  •  Solder JTAG cable to LG E405 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E405 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.
lg_e405_optimus_l3_dual

RIFF JTAG – LG E615 Optimus L5 Dual Unbrick – Dead boot repair supported

Posted on by

29.03.2013   RIFF JTAG – LG E615 Optimus L5 Dual Unbrick – Dead boot repair supported

Repairing bricked LG E615 with the RIFF Box is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect LG E615:

  •  Solder JTAG cable to LG E615 JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure LG E615 is selected in the list of models;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods

To enter emergency mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume down’ key and press ‘Power ON’ button.

.
lg_e610_optimus_l5

RIFF JTAG – Samsung GT-i8190 Galaxy S III Mini Unbrick – Dead boot repair supported

Posted on by

29.03.2013  RIFF JTAG – Samsung GT-i8190 Galaxy S III Mini Unbrick – Dead boot repair supported

Repairing bricked Samsung I8190 is easy with the RIFF Box.
Please note, USB cable must be either disconnected or connected to PC. Charger is not allowed. In order to establish connection, insert battery and press Power On.
Problem to establish JTAG connection means the device is dead up to the loader which enables JTAG. In this case phone must be detected via USB cable as “U8500 USB ROM”. Please install drivers which are located in JTAG Manager “Drivers\NTU8500” folder, leave USB cable connected and start resurrection again.

To resurrect Samsung I8190:

  •  Solder JTAG cable to Samsung I8190 JTAG pads;
  •  Attach battery and connect USB cable;
  •  Make sure Samsung I8190 is selected in the list of models;
  •  Click Resurrect button;
  •  If required, press Power On key;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.
samsung_gt-i8190_galaxy_s_iii_mini_2