RIFF JTAG – Easy repair HTC Desire 600 (HTC CP3) supported

Repairing bricked HTC Desire 600 (PO4911000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0001 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PO4911000’.

To resurrect HTC Desire 600 (PO4911000):

•  Solder JTAG cable to HTC Desire 600 (PO4911000) JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure HTC Desire 600 (PO4911000) is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Easy repair HTC Butterfly S 901s 4G LTE supported

Repairing bricked HTC Butterfly S (PO6821000) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.54.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID may be re-flashed too. In this case after resurrection the phone will have Model ID = ‘PO6821000’.

To resurrect HTC Butterfly S (PO6821000):

•  Solder JTAG cable to HTC Butterfly S (PO6821000) JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure HTC Butterfly S (PO6821000) is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

RIFF JTAG – Easy repair Micromax A87 Ninja 4.0 supported

Repairing bricked Micromax A87 is easy with the RIFF Box.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Currently supported resurrection for NAND memories with 2KB page size.

To resurrect Micromax A87:

•  Solder JTAG cable to Micromax A87 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure Micromax A87 is selected in the list of models;
•  If you use battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

.

RIFF JTAG – Easy repair Huawei Ideos X3 U8510-1 (Huawei Blaze) supported

Repairing bricked Huawei U8510-1 is easy with the RIFF Box.

To resurrect Huawei U8510-1:

•  Solder JTAG cable to Huawei U8510-1 JTAG pads;
•  Connect Huawei U8510-1 tablet’s charger for power;
•  Make sure Huawei U8510-1 is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.

RIFF JTAG – Easy repair Alcatel One Touch OT-993D supported

Repairing bricked ALCATEL OT993D is easy with the RIFF Box.

To resurrect ALCATEL OT993D:

•  Solder JTAG cable to ALCATEL OT993D JTAG pads;
•  Make sure ALCATEL OT993D is selected in the list of models;
•  Connect USB Data Cable;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

.

RIFF JTAG – Easy repair HUAWEI Ascend G600 (U8950-1) supported

Repairing bricked Huawei U8950-1 is easy with the RIFF Box.

To resurrect Huawei U8950-1:

•  Solder JTAG cable to Huawei U8950-1 JTAG pads;
•  Connect Huawei U8950-1 tablet’s charger for power;
•  Make sure Huawei U8950-1 is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Copy ‘dload’ folder from firmware update package to SD card root;
•  Insert SD card into the SD slot;
•  Insert battery;
•  Hold both ‘Volume Down’ and ‘Volume up’ keys and press Power-On.

.

RIFF JTAG – Easy repair Samsung GT-i8190N Galaxy S III Mini NFC supported

Repairing bricked Samsung I8190N is easy with the RIFF Box.
Please note, USB cable must be either disconnected or connected to PC. Charger is not allowed. In order to establish connection, insert battery and press Power On.
Problem to establish JTAG connection means the device is dead up to the loader which enables JTAG. In this case phone must be detected via USB cable as “U8500 USB ROM”. Please install drivers which are located in JTAG Manager “Drivers\NTU8500” folder, leave USB cable connected and start resurrection again.

To resurrect Samsung I8190N:

•  Solder JTAG cable to Samsung I8190N JTAG pads;
•  Attach battery and connect USB cable;
•  Make sure Samsung I8190N is selected in the list of models;
•  Click Resurrect button;
•  If required, press Power On key;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Easy repair Samsung B5512 Galaxy Y Pro Duos supported

Repairing bricked Samsung B5512 is easy with the RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung B5512:

•  Solder JTAG cable to Samsung B5512 JTAG pads;
•  Connect USB cable to phone and PC;
•  Insert battery;
•  Make sure Samsung B5512 is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
•  If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

.

RIFF JTAG – Easy repair Samsung GT-i9192 Galaxy S4 Mini Duos (Samsung Serrano) supported

Repairing bricked Samsung I9192 is easy with the RIFF Box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.

To resurrect Samsung I9192:

•  Solder JTAG cable to Samsung I9192 JTAG pads;
•  Insert USB Data cable into board and PC;
•  Make sure Samsung I9192 is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

RIFF JTAG – Easy repair Samsung GT-i8262 Galaxy Core Duos supported

Repairing bricked Samsung I8262 is easy with the RIFF Box.

To resurrect Samsung I8262:

•  Solder JTAG cable to Samsung I8262 JTAG pads;
•  Connect Samsung I8262 tablet’s charger for power;
•  Make sure Samsung I8262 is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.